manualshive.com logo in svg

Emerson Rosemount Xi, Reference Manual, Page: 17 / 82

Share
Download
Emerson Rosemount Xi Reference Manual Download Page 17

2.2.1

Mount

The Rosemount Xi Advanced Electronics is available in a panel mounting, wall mounting,
or pipe mounting configuration.

Refer to 

Figure 2-2

 or 

Figure 2-3

 for the panel, wall, or pipe mounting details.

1. Ensure all components are available to install the Rosemount Xi.
2. Select a mounting location near or removed from the O

2

 probe.

Consider the temperature limitations of the Rosemount Xi (see 

Specifications

)

when selecting the mounting location.

3. Mount the Rosemount Xi at a height convenient for viewing and operating the

interface.
Approximately 5 ft (1.5 m) is recommended.

4. The keypad window on the Rosemount Xi may have interior and exterior protective

membranes. Remove the protective membranes prior to use of the Rosemount Xi
enclosure.

NOTICE

Failure to remove the protective membranes may cause the display to appear
distorted. The membrane may be difficult or impossible to remove after extended
use at elevated temperatures.

Reference Manual 

Install

00809-0100-4889

October 2022

Emerson.com/Rosemount

17

Summary of Contents for Rosemount Xi



















































































Reviews:

No comments