manualshive.com logo in svg

Emerson Rosemount 8800D Series, Quick Installation Manual

Share
Download
Emerson Rosemount 8800D Series Quick Installation Manual Download Page 9

Quick Installation Guide

00825-0100-4004, Rev DB

December 2011

Rosemount 8800D

8

CAUTION

Do not rotate the housing while the sensor cable is attached to the base of the housing. This 
will stress the cable and may damage the sensor.

6. Place the electronics housing into the top of the support tube.

7. Use a 5/32” hex wrench to turn the three housing rotation screws counter-clockwise 

(outward) to engage the support tube.

S

TEP

 3: S

ET

 J

UMPERS

Adjust jumpers to desired settings.

HART

If alarm and security jumpers are not installed, the flowmeter will operate normally with the 
default alarm condition alarm 

high

 and the security 

off

.

Figure 9.  HART Jumpers and LCD

F

OUNDATION

 fieldbus

If security and simulate enable jumpers are not installed, the flowmeter will operate normally 
with the default security 

off 

and simulate enable

 off

. 

Figure 10.  F

OUNDATION

 fieldbus Jumpers and LCD

ALARM

HI

LO

ON

OFF

SECURITY

SIMULATE ENABLE

OFF

ON

ON

OFF

SECURITY

4004_RevDB.fm  Page 8  Wednesday, November 23, 2011  3:06 PM

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for Rosemount 8800D Series































Reviews:

No comments

Brands by name

Popular brands

Load more brands