manualshive.com logo in svg

Emerson Rosemount 228, Reference Manual, Page: 8 / 44

Share
Download
Emerson Rosemount 228 Reference Manual Download Page 8

Maximum operating temperature and pressure

 (continued)

Table 1-2:   

Body material option

Maximum temperature

Maximum pressure

Maximum pressure (for
CRN registration only)

-03 (Glass-filled PEEK (high
temperature))

392 °F (200 °C)

295 psig (2135 kPa)

220 psig (1618 kPa [abs])

-04 (Glass-filled Tefzel)

248 °F (120 °C)

200 psig (1480 kPa)

150 psig (1135 kPa [abs])

-05 (Unfilled Tefzel)

248 °F (120 °C)

200 psig (1480 kPa)

150 psig (1135 kPa [abs])

Insertion adapter specifications

Table 1-3:   

Adapter
part num-
ber

Sensor com-
patibility

Process con-
nection

Wetted ma-
terials

Maximum
tempera-
ture

Maximum
pressure

Maximum
pressure
(for CRN
registration
only)

Weight /
shipping
weight

23242-02

For use with
option -21

1-1/2 in.
MNPT

316 stainless
steel, glass-
filled PEEK,
Viton

392 ° F
(200 °C)

295 psig
(2135 kPa)

220 psig
(1618 kPa
[abs])

3 lb / 4 lb
(1.5 kg / 2.0
kg)

23242-03

For use with
option -20

1-1/2 in.
MNPT

316 stainless
steel, glass-
filled PEEK,
Viton

392 °F
(200 °C)

295 psig
(2135 kPa)

220 psig
(1618 kPa
[abs])

3 lb / 4 lb
(1.5 kg / 2.0
kg)

2001990

For use with
option -21

2 in. MNPT

CPVC
Viton

100 °F
(38 °C)

100 psig
(791 kPa
[abs])

N/A

1 lb / 2 lb
(0.5 kg / 1.0
kg)

185 °F (85 °
C)

45 psig (412
kPa [abs])

Retraction assembly specfications

Table 1-4:   

Specification

Description

Sensor compatibility

The retraction assemblies are used with 228 - [ ]-20-54-62
only

Wetted materials

315 stainless steel, ethylene polypropylene (EP), unfilled
Teflon, carbon-filled Teflon

Process connection

1 - 1/2 in. MNPT

Maximum operating condition

392 °F (200 °C), 295 psig (2135 kPa [abs])

Description and specifications

2

 Reference Manual

Summary of Contents for Rosemount 228













































Reviews:

No comments