Emerson Rosemount 1151 Quick Installation Manual Download | Manualshive

Page: 18 / 22

background image

Quick Installation Guide

00825-0100-4593, Rev BA

July 2009

Rosemount 1151

18

N7

Type N
Certificate Number: Aus Ex 122X
Ex n IIC T5 (T

a

= 80 °C) / T6 IP66

Special Conditions for safe use (x):

1. It is a condition of safe use that a nominal voltage of 30 V for Ex n application shall

not be exceeded.

2. It is a condition of safe use that when the optional transient protection is used its

metallic housing shall be bonded to the system earth.

Combination Certifications

Stainless steel certification tag is provided when optional approval is specified. Once a
device labeled with multiple approval types is installed, it should not be reinstalled using any
other approval types. Permanently mark the approval label to distinguish it from unused
approval types.

C6

Combination of I6 and E6, CSA Explosion Proof and Intrinsic Safety Approval. Factory Sealed.

K5

Combination of FM Explosion Proof, Intrinsic Safety, and Non-incendive Approvals.

K6

Combination of E6, I6, I1, and E8.

4593_Rev_BA.fm Page 18 Friday, August 7, 2009 3:38 PM

«
...
16
17
18
19
20
...
»

Summary of Contents for Rosemount 1151























Reviews:

No comments

Related manuals for Rosemount 1151

Brand: Nautel Pages: 20

Brand: Icom Pages: 40

Brand: Omega Pages: 4

sigfox RC4 PULSE V3

Brand: Adeunis RF Pages: 27

Brand: M-system Pages: 3

Brand: M-system Pages: 3

Brand: SICK STEGMANN Pages: 8

AN/PRC-117D Series

Brand: Harris Pages: 40

Brand: EI Pages: 41

Brand: RIDGID Pages: 20

Brand: Sennheiser Pages: 8

Brand: Redback Pages: 4

Brand: E+E Elektronik Pages: 3

Brand: Codan Pages: 115

CamLock UPM PM1RM

Brand: B-K lighting Pages: 9

Brand: Advanced Microwave Products Pages: 2

Brand: Vertex Standard Pages: 40

Brand: Mianyang Weibo Electronic Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands