background image

Quick Installation Guide

00825-0100-4593, Rev BA
July 2009

Rosemount 1151

13

S

TEP

 6: T

RIM

 

THE

 T

RANSMITTER

NOTE

Transmitters are shipped fully calibrated per request or by the factory default of full scale 
(span = upper range limit).

Full Trim

A full trim is a two-point sensor calibration where two end-point pressures are applied, and 
the transmitter process variable output is adjusted to agree with the pressure input.

Using the HART Communicator

Zero Trim 

A zero trim is a single-point adjustment used for compensating mounting position effects. 
When performing a zero trim, ensure that the equalizing valve is open and all wet legs are 
filled to the correct level. If zero offset is less than 3% of true zero, follow the “Using the 
HART Communicator” instructions below. If zero offset is greater than 3% of true zero, follow 
the “Using the Transmitter Zero Adjustment Buttons” instructions.

Using the HART Communicator

HART Fast Keys

Steps

1, 2, 3, 3

1. Equalize or vent the transmitter and connect HART 

communicator.

2. At the menu, input the HART Fast Key sequence.
3. Follow the commands to perform a full trim.

HART Fast Keys

Steps

1, 2, 3, 3, 1

1. Equalize or vent the transmitter and connect HART 

communicator.

2. At the menu, input the HART Fast Key sequence.
3. Follow the commands to perform a zero trim.

4593_Rev_BA.fm  Page 13  Friday, August 7, 2009  3:38 PM

Summary of Contents for Rosemount 1151























Reviews: