background image

15 

1/2” 

95 

65 

4 x 14

20 

3/4” 

105 

75 

4 x 14

25 

1” 

115 

85 

4 x 14

40 

1 1/2” 

150 

110 

4 x 18

50 

2” 

165 

125 

4 x 18

65 

2 1/2” 

185 

145 

4 x 18

80 

3” 

200 

160 

8 x 18

100 

4” 

220 

180 

8 x 18

150* 

6” 

279 

241 

8 x 22

15 

1/2” 

89 

60.3 

4 x 16

20 

3/4” 

98 

70.0 

4 x 16

25 

1” 

108 

79.5 

4 x 16

40 

1 1/2” 

127 

98.5 

4 x 16

50 

2” 

152 

120.5 

4 x 19

65 

2 1/2” 

185 

145.0 

4 x 19

80 

3” 

190 

152.5 

4 x 19

100 

4” 

229 

190.5 

8 x 19

6” 

279 

241.0 

8 x 22

15 

1/2” 

95 

70 

4 x 15

20 

3/4” 

100 

75 

4 x 15

25 

1” 

125 

90 

4 x 19

40 

1 1/2” 

140 

105 

4 x 19

50 

2” 

155 

120 

4 x 19

65 

2 1/2” 

175 

140 

4 x 19

80 

3” 

185 

150 

8 x 19

100 

4” 

210 

175 

8 x 19

6” 

279 

241 

8 x 22

SNB-SNC ball valves

Installation and Maintenance Instructions

Emerson reserves the right to change the contents without notice 

page 4

6.5. Installation options

Ball valves can be equipped with various means of operation e.g. with hand lever, handwheel, 
electrical, pneumatic or hydraulic drive, or with a drive linked to a position controller for SNC 
control valves. The hand levers are supplied complete with a notched plate which allows the lever 
to be latched either in the end positions only (version ZE) or in the end positions and additionally 
in various intermediate positions (version Z). In addition, the hand lever can be provided with limit 
switches which indicate ‘open’ or ‘closed’.
For installation in exposed places, shaft extensions in various lengths are available for all sizes.

6.6. Bolted joints in the pipeline

All flange bolts must be used, even on low-pressure systems. The specified tightening toques for 
the bolts must always be adhered to.

6.7. Body variants

SNB and SNC ball valves have the same body dimensions. The face-to-face and mounting flange 
dimensions of the ball valve bodies vary according to the various standards. When used as an end 
of line valve, it must be secured in such a way that access to the isolating valve is restricted when 
in service.
It should also be noted that when a valve is used as the end valve of a pressurized system, the 
flange must be removed from the valve.

Dimensions

 

DN 

 

Tk 

n x d

mm 

 

inches 

mm mm mm

6.2. Dimensions of the mounting flanges for SNB-SNC ball and C valves DIN-PN16

* DN 150 ball valve only as ANSI 6” version available

Dimensions

 

DN 

 

Tk 

n x d

mm 

 

inches 

mm mm mm

6.3. Dimensions of the mounting flanges for SNB-SNC valves ANSI B 16.10 class 150 (lbs)

Dimensions

 

DN 

 

Tk 

n x d

mm 

 

inches 

mm mm mm

6.4. Dimensions of the mounting flanges for SNB-SNC ball and C valves JIS-10K

* Ball valves DN 150 only as ANSI 6” version available

Summary of Contents for NEOTECHA SNB Series








Reviews: