Emerson Liebert APM 120 Manual Download Page 57

Page: 57 / 144

Battery Installation

Liebert

APM

™

5.3

UPS Batteries—Liebert APM 45kVA Frame Only

The Liebert APM’s internal batteries are fully charged before the unit is shipped. During storage and

transportation, some charge is lost. All batteries should be recharged before use. The battery charger

works only when the Liebert APM is connected to input power and turned On.

5.3.1 Internal Battery Breaker Component Locations and Control Wiring

The Liebert APM 45kVA frame contains internal batteries. The batteries are protected by an internal

battery breaker.

Figure 34

shows the component location;

Figure 35

shows the control wiring.

Figure 34 Internal battery breaker component locations

NOTE

Full safety instructions concerning the use and maintenance of UPS batteries are provided in

the appropriate battery manufacturer's manuals, available on the manufacturer’s Web site.
The battery safety information contained in this section relates to key considerations that must

be taken into account during the installation design process and might affect the design

outcome, depending on your installation.

UAM04052A
Pg. 1, Rev. 0

UHRF3S67X2
Liebert APM
Bypass Module

Battery
Temperature
Sensor
Location

Battery
Breaker

See
Detail A

Detail A

FRONT

TB1

UH8351A8
Capacitor
Board

UHW241C2
BIB Board

See Figure 35

Summary of Contents for Liebert APM 120

















































































































































Search results

Summary of Contents for Liebert APM 120

Reviews:

Related manuals for Liebert APM 120

Brands by name

Popular brands

Emerson Liebert APM 120, Manual

Search results

Summary of Contents for Liebert APM 120

Reviews:

Related manuals for Liebert APM 120

Brands by name

Popular brands