background image

BRIC30S/BRIC30N User Manual

1

Contents
Introduction

......................................................................................................................... 2

1. Safety Precautions

...................................................................................................... 3

1.1. Important Rules

................................................................................................... 3

1.2. Symbols

................................................................................................................ 4

2. Product Introduction

.................................................................................................... 5

2.1. General Characteristics

...................................................................................... 5

2.2. Special Features

.................................................................................................. 5

3. Unpacking and Installation

......................................................................................... 7

3.1. Environmental Requirements

............................................................................ 7

3.2. Easy Installation and Removal

.......................................................................... 9

3.3. Electrical Installation

......................................................................................... 10

3.4. Comm. Port Description

................................................................................... 14

4. Operating Mode and Instructions

............................................................................ 16

4.1. Operating Mode

................................................................................................. 17

4.2. Single Unit Operation

....................................................................................... 17

4.3. Parallel Mode Operation

.................................................................................. 20

4.4. LED Display

....................................................................................................... 22

5. Monitoring Platform

................................................................................................... 23

5.1. Panel

................................................................................................................... 23

6. Communications interface:

....................................................................................... 35

6.1. RS-232 interface

............................................................................................... 35

6.2. RS-485 interface

............................................................................................... 35

7. Troubleshooting

......................................................................................................... 36

8. Maintenance

............................................................................................................... 37

8.1. Regular Maintenance

....................................................................................... 37

8.2. Battery

................................................................................................................. 37

8.3. Fan

...................................................................................................................... 37

8.4. Capacitor

............................................................................................................ 37

8.5. Fuse

.................................................................................................................... 37

9. Accessories and Options

.......................................................................................... 38

9.1. Accessories

........................................................................................................ 38

9.2. Options

................................................................................................................ 40

10.Specification

............................................................................................................... 41

Summary of Contents for BRIC30N























Reviews: