Emerson Fisher Control-Disk NPS 14 CL150 Instruction Manual Download Page 21 | Manualshive

Page: 21 / 28

background image

Instruction Manual

D103545X012

Control-Disk NPS 14-36

April 2011

21

Retrofit Kits

Retrofit kits include all parts required for installation of the ENVIRO‐SEAL packing system into existing
high‐performance butterfly valves. Retrofit kits are available for single PTFE packing.

See table 7 for retrofit kit part numbers.

Retrofit Kit Included Parts

Key

Description

Quantity

10
17

100
101
102
103
105
106
107
111
112

Anti‐blowout follower

Jam nut

Packing stud

Packing nut

Packing flange

Spring pack assembly

Packing Set

Anti‐extrusion washer

Packing box ring

Tag

Cable

1
1
2
2
1
1
1

2

(1)

2

(2)

1
1

1. Not included in graphite packing kit.
2. Only 1 req'd for NPS 18 CL300, NPS 20 CL150 and NPS 24 CL150.

Note: Key 103, the spring pack assembly, is made up of the packing spring stack held in place by an O‐ring on the
packing follower.

Repair Kits

PTFE Repair kits include a single PTFE packing set and anti‐extrusion washers. Graphite packing sets include graphite
packing rings and carbon anti‐extrusion rings. See table 7 for PTFE repair kit part numbers.

Table 7. Retrofit and Repair Kit Part Numbers

VALVE SIZE, NPS

PRESSURE RATING

SHAFT

DIAMETER

(1)(2)

,

mm (Inch)

RETROFIT KITS

REPAIR KITS

PTFE

PTFE

14

CL150

34.9 (1‐3/8)

RRTYXRT0592

RRTYX000172

CL300

50.8 (2)

RRTYXRT0602

RRTYX000182

16

CL150

38.1 (1‐1/2)

RRTYXRT0612

RRTYX000192

CL300

57.2 (2‐1/4)

RRTYXRT0622

RRTYX000202

18

CL150

44.5 (1‐3/4)

RRTYXRT0632

RRTYX000212

CL300

63.5 (2‐1/2)

RRTYXRT0642

RRTYX000222

20

CL150

50.8 (2)

RRTYXRT0652

RRTYX000182

24

CL150

63.5 (2‐1/2)

RRTYXRT0662

RRTYX000222

30, 36

No kit available

1. Shaft diameter: Diameter through the packing box.
2. For larger shaft sizes, consult your Emerson Process Management sales office.

«
...
19
20
21
22
23
...
»

Summary of Contents for Fisher Control-Disk NPS 14 CL150





























Reviews:

No comments

Related manuals for Fisher Control-Disk NPS 14 CL150

Brand: Lattice Semiconductor Pages: 30

Brand: WAFER Pages: 15

ServeRAID M5014

Brand: IBM Pages: 106

SmartSwitch 6000

Brand: Cabletron Systems Pages: 76

Brand: Barthelme Pages: 8

Brand: CAB Pages: 28

Brand: C-TEC Pages: 16

Brand: C&T Solution Pages: 27

SECURIT ST800L+

Brand: C&K systems Pages: 16

Brand: Quectel Pages: 95

Brand: ICAS Pages: 51

Brand: Icar Pages: 40

Brand: Icar Pages: 86

Brand: Icar Pages: 39

Brand: IBP Pages: 12

BT300 BurnerTronic

Brand: Lamtec Pages: 48

Brand: Koer Pages: 6

Brand: Vag Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands