background image

Page: 

  

Falkevej 12 

DK – 6705 Esbjerg Ø 

Tel.: +45 79 14 22 22

 

Pages incl. this one: 

Init.: 

CEH

 

Date: 

110207 

Approved: 

 

Drawing No.: 

8181101 

Version:

 

01 

Supplyer: 

 

Subject: 

Instr. XR30CX GB (medsendes fra termostat) 

 

Components must comply with the rules and restrictions stated in A/S Vestfrosts List of undesirable components/substances, and be 

free from silicone. 

 

This component must comply with the European Directive 2002/95/EC on the restriction of the use of certain hazardous substances in 

electrical and electronic equipment (RoHS directive). 

 

This drawing is the property of A/S Vestfrost and must not be copied, passed on to, or otherwise used by any person without the 

express consent of A/S Vestfrost.

Date: Last 

modification: 

Init: 

 

 

 

 
 
 
 

 

Denne vare er specificeret ved nedenstående datablad. Med forudgående skriftlig 

tilladelse fra Vestfrost, kan alternativ type/fabrikat anvendes. 

This product is specified according to the data sheet mentioned below. Alternative products/product types may only be used with the 

prior written consent of A/S Vestfrost. 

 
 
 
 
 
 

 
 
 
 

Se vedlagte 

Summary of Contents for Dixell XR30CX-4S1C1






Reviews: