Emerson Dixell Universal-R Installing And Operating Instructions Download Page 3

Page: 3 / 20

1592031000 Univ-R4 GB - r1.1 - 2012.07.23 Universal-R

3/20

INDEX

INDEX____________________________________________________________________________________3

GENERAL WARNING _______________________________________________________________________4

GENERAL DESCRIPTION ___________________________________________________________________4

QUICK START UP PROCEDURE – Up and running in 5 easy steps __________________________________5

TYPICAL CONNECTIONS - FOR GENERAL GUIDANCE ONLY _____________________________________6

PARAMETER TABLE and factory default settings _________________________________________________7

PARAMETERS – THEIR FUNCTIONS IN DETAIL _______________________________________________10

BUTTONS AND THEIR FUNCTIONS__________________________________________________________15

PROGRAMMING MODE ____________________________________________________________________15

10.

OTHER FEATURES OF THE UNIVERSAL-R ___________________________________________________16

11.

THERMOSTAT OVERRIDE ( not available when parameter tC = 1 or 7 )______________________________16

12.

DEFROST TYPES _________________________________________________________________________16

13.

EVAPORATOR FAN CONTROL (only when parameter tC = 5 or 6) __________________________________16

14.

SPECIAL APPLICATIONS – DEAD BAND CONTROL ____________________________________________17

15.

ALARMS_________________________________________________________________________________17

16.

REMOVING SECURITY LEVEL PROTECTION __________________________________________________17

17.

MOUNTING ______________________________________________________________________________18

18.

ELECTRICAL CONNECTIONS _______________________________________________________________18

19.

PROBES_________________________________________________________________________________18

20.

TECHNICAL DATA ________________________________________________________________________18

21.

FAULT FINDING _________________________________________________________________________19

Summary of Contents for Dixell Universal-R





















Search results

Summary of Contents for Dixell Universal-R

Reviews:

Related manuals for Dixell Universal-R

Brands by name

Popular brands

Emerson Dixell Universal-R, Installing And Operating Instructions

Search results

Summary of Contents for Dixell Universal-R

Reviews:

Related manuals for Dixell Universal-R

Brands by name

Popular brands