Emerson Copeland Scroll ZP K3 Series Page 2 Bulletin Download

Page: 2 / 25

AE4-1365 R4

Safety Instructions

Copeland Scroll

™

compressors are manufactured according to the latest U.S. and European Safety

Standards. Particular emphasis has been placed on the user's safety. Safey icons are explained below

and safety instructions applicable to the products in this bulletin are grouped on Page 3. These

instructions should be retained throughout the lifetime of the compessor.

You are strongly advised

to follow these safety instructions.

Safety Icon Explanation

DANGER indicates a hazardous situation which, if not avoided, will result

in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION, used with the safety alert symbol, indicates a hazardous

situation which, if not avoided, could result in minor or moderate injury.

NOTICE is used to address practices not related to personal injury.

CAUTION, without the safety alert symbol, is used to address practices

not related to personal injury.

DANGER

WARNING

CAUTION

NOTICE

CAUTION

Summary of Contents for Copeland Scroll ZP K3 Series


























Search results

Summary of Contents for Copeland Scroll ZP K3 Series

Reviews:

Related manuals for Copeland Scroll ZP K3 Series

Brands by name

Popular brands

Emerson Copeland Scroll ZP K3 Series, Bulletin

Search results

Summary of Contents for Copeland Scroll ZP K3 Series

Reviews:

Related manuals for Copeland Scroll ZP K3 Series

Brands by name

Popular brands