Emerson CF370BQ00 Owner'S Manual Download Page 29

Page: 29 / 32

emersonfans.com

Please contact 1-800-654-3545 for further assistance

ETL Model No.: CF370

Before discarding packaging material, be certain all parts have been removed.

HOW TO ORDER REPAIR PARTS

WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:
• PART NUMBER

• NAME OF ITEM

• PART DESCRIPTION • MODEL NUMBER
The model number of your Fan will be found on a label attached to the top housing.
For repair parts, phone 1-800-654-3545.

14. Repair Parts Listing

Part Numbers

Key

Model Number Model Number Model Number Model Number Model Number

No. Description

CF370BS00

CF370BQ00

CF370GRT00 CF370ORB00 CF370SW00

Hanger Ball Assembly, Consisting of:

761655-17

761655-19

761655-102

761655-32

761655-92

Hanger Bracket (1)

—

Hanger Ball (1)

—

4.5” Downrod Assembly (1)

—

Ceiling Cover (1)

764885-BS

764885-BQ

764885-GRT

764885-ORB

764885-SW

Motor Coupler Cover (1)

765011-BS

765011-BQ

765011-GRT

765011-ORB

765011-SW

Wiring Harness (1)

765015

Lower Housing (1)

765020-BS

765020-BQ

765020-GRT

765020-ORB

765020-SW

LED Light Fixture Assembly (1)

764898

Shade (1)

765023

Fan Blades (3)

765018-BS

765018-CR

765018-TM

765018-AO

765018-SW

Receiver w/Hardware (1)

RCFP

4 Speed Wall Control w/Hardware (1)

SW406

Parts Bag Containing:

765024-CRM

765024-BLX

765024-SW

Wire Connectors, 12 ga. (5)

—

Threaded Studs, #8-32 x 1-1/4” (2)

—

Lockwashers, #8 External Tooth (2)

—

Knurled Knobs, #8-32 (2)

—

Clevis Pin (1)

—

Hairpin Clip (1)

—

#10-24 x 11 mm Washer Head

Blade Screws (10)

—

#6-32 x 3/8” Truss Head Screw

w/Lockwasher (1 spare)

—

#6-32 x 1/4 Truss Head Screws

w/Lockwashers (4)

—

Balancing Kit (1)

—

— Owner’s Manual

BP7543

Summary of Contents for CF370BQ00

































Search results

Summary of Contents for CF370BQ00

Reviews:

Related manuals for CF370BQ00

Brands by name

Popular brands

Emerson CF370BQ00, Owner'S Manual

Search results

Summary of Contents for CF370BQ00

Reviews:

Related manuals for CF370BQ00

Brands by name

Popular brands