background image

Enardo 860 and 960 Series Spring-Loaded 

Pressure/Vacuum Relief Valve (ATEX Approved)

Table of Contents

Introduction ..................................................................1
Specifications ..............................................................2
Product Identification and Marking ..............................4
Principle of Operation ..................................................4
Installation ...................................................................5
Maintenance ................................................................9
Weight Information .................................................... 11
Valve Repair .............................................................. 11

 

 WARNING

Failure to follow these instructions or 

to properly install and maintain this 

equipment could result in an explosion, 

fire and/or chemical contamination 

causing property damage and personal 

injury or death.
Fisher™ spring-loaded pressure/vacuum 

relief valve must be installed, operated 

and maintained in accordance with 

federal, state and local codes, rules 

and regulations, and Emerson Process 

Management Regulator Technologies 

Tulsa, LLC (Emerson) instructions.
Failure to correct trouble could result in 

a hazardous condition. Call a qualified 

service person to service the unit. 

Installation, operation and maintenance 

procedures performed by unqualified 

person may result in improper adjustment 

and unsafe operation. Either condition may 

result in equipment damage or personal 

injury. Only a qualified person shall install 

or service the spring-loaded pressure/

vacuum relief valve.

Figure 1. 

Enardo

 

Model 860 Spring-Loaded Pressure/ 

Vacuum Relief Valve

Figure 2.

 Enardo Model 960 Spring-Loaded Pressure/ 

Vacuum Relief Valve

Introduction

Scope of the Manual

This Instruction Manual provides instructions for 

installation, maintenance and parts ordering information 

for the Enardo 860 and 960 Series spring-loaded 

pressure/vacuum relief valve (SL-PVRV).

Instruction Manual

D103814X012
February 2022

Enardo 860 and 960 Series

Outside North 

America Only

Summary of Contents for 963













Reviews: