eMachines VC31 Manual Download Page 23 | Manualshive

Page: 23 / 52

background image

2 - 13

Installation Procedures

Power LED

is connected with the system power indicator to indicate whether

the system is on/off. It will blink when the system enters suspend mode.

IR

is used to communicate with another IR device via a 4-wire plug.

Reset Button

is connected to the reset button. Push this switch to reboot the

system instead of turning the power button off and on.

HDD LED

is connected to the IDE device indicator. This LED will blink when

the hard disk drives are activated.

LED(G)

is in green light when the system in power on status.

LED(Y)

is in yellow light when the system in suspend mode.

Power Button

is connected with power button. Push this switch allows the

system to be turned on and off rather than using the power supply button.

Suspend Button

is connected with suspend button. To enter the system into

power saving mode, simply press this button when the system is in full-on

mode.

Speaker

is connected with the case speaker.

PS/2 Keyboard and Mouse Connector

These two 6-pin female (PS/2 keyboard is purple color and PS/2 mouse is

green color) connectors are used for your PS/2 keyboard and PS/2 mouse.

«
...
21
22
23
24
25
...
»

Summary of Contents for VC31





















































Reviews:

No comments

Related manuals for VC31

Brand: IEI Technology Pages: 211

Brand: IEI Technology Pages: 8

Brand: IEI Technology Pages: 8

TPS53355EVM-864

Brand: Texas Instruments Pages: 29

Brand: Aaeon Pages: 120

Brand: Texas Instruments Pages: 16

Brand: Yamaha Pages: 223

Brand: Inrevium Pages: 57

Brand: IEI Technology Pages: 21

Brand: MSI Pages: 45

Brand: Analog Devices Pages: 13

STEVAL-LLL002V1

Brand: STMicroelectronics Pages: 29

Brand: EPC Pages: 6

Brand: Gigabyte Pages: 88

Brand: MSI Pages: 92

CT-PBT01 Series

Brand: C&T Solution Pages: 48

Brand: Fujitsu Pages: 12

ADA-91270-90340-100PFV

Brand: Fujitsu Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands