eMachines D845GVSR Page 21 User Manual Download | Manualshive

Page: 21 / 34

background image

2-11

Using the BIOS Setup Program

Feature Options Description

1st Drive

Dependent on

Specifies the boot sequence from the available removable devices.

installed

To specify boot sequence:

removable
devices

Removable Devices Submenu

This submenu is for setting removable device priority.

Feature Options Description

1st Drive

Dependent on

Specifies the boot sequence from the available hard disk drives. To

installed hard

specify boot sequence:

drives

1. Select the boot device with <

> or <

>.

2. Press <Enter> to set the selection as the intended boot device.

1. Select the boot device with <

> or <

>.

2. Press <Enter> to set the selection as the intended boot device.

Hard Disk Drives Submenu

This submenu is for setting hard disk drive priority.

Boot Device Priority Submenu

You can select the boot sequence from the available devices.

To specify boot sequence:

1. Select the boot device with <

> or <

>.

2. Press <+> to move the device up the list or <-> to move the device down the list.

«
...
19
20
21
22
23
...
»

Summary of Contents for D845GVSR



































Reviews:

No comments

Related manuals for D845GVSR

Brand: Abit Pages: 120

Brand: DFI Pages: 99

Brand: Texas Instruments Pages: 101

945GC MICRO 775

Brand: Biostar Pages: 49

Brand: AOpen Pages: 8

JetBox 9310 Series

Brand: Korenix Pages: 21

Brand: Texas Instruments Pages: 19

Brand: Acorp Pages: 74

Brand: Gigabyte Pages: 36

Brand: ON Semiconductor Pages: 8

Brand: National Semiconductor Pages: 22

Brand: Gigabyte Pages: 38

Brand: AOpen Pages: 11

Brand: Micronics Pages: 63

Brand: ASROCK Pages: 97

Brand: ASROCK Pages: 2

Brand: OLIMEX Pages: 14

Brand: Socket Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands