ELZAB CAT 27 NEPTUN 2 User Manual Download Page 15 | Manualshive

Page: 15 / 32

ELZAB CAT 27 NEPTUN 2 User Manual Download Page 15

14

User Manual CAT 27 scales series

ELZAB S.A.

5.2.

User menu

Structure of the

USER MENU

is shown below. Default values are marked with “

^

”.

USER MENU

Entrance to the menu: enter the PASSWORD 1 (press 2 x the

key and

after press 2 x the

key and confirm with the

key).

01 PROTOCOL TYPE

*

01

ELZAB BASIC

02^ ELZAB EXTENDED

03

CAS

02 RESULT COMPONENTS

01

WEIGHT

02^

AUTOMATICALLY

03

WT + PRICE + VALUE

03 BAUD RATE

01

1200 bits/sec

02

2400 bits/sec

03

4800 bits/sec

04^ 9600 bits/sec

05

19200 bits/sec

06

28800 bits/sec

07

38400 bits/sec

08

57600 bits/sec

04 PARAMETERS

01

7-EVEN-1

02

7-ODD-1

03

7-SPACE-1

04

7-MARK-1

05

8-NONE-1

06^ 8-EVEN-1

07

8-ODD-1

08

8-SPACE-1

09

8-MARK-1

05 PARITY CHECKING

01^ NO CHECKING

02

CHECKING ENABLED

06 STABIL. CONDITION

01

HIGHEST STABILITY

02^ HIGH STABILITY

03

LOW STABILITY

04

LOWEST STABILITY.

07 MINIMUM RESULT

01

00 x e

02^ 01 x e

03

02 x e

04

04 x e

05

05 x e

06

10 x e

07

20 x e

«
...
13
14
15
16
17
...
»

Summary of Contents for CAT 27 NEPTUN 2

































Reviews:

No comments