background image

 

 

CMi6140 

User’s Manual English 

 

 

 

 

 

 

 

 

 

 

 

 

CMi6140 

User’s Manual English 

page | 4 (38) 

[2022-09] 

 

V1.2 

 

 

 

 

1  Document notes 

All information in this manual, including product data, diagrams, charts, etc. represents information on 
products at the time of publication, and is subject to change without prior notice due to product 
improvements or other reasons. It is recommended that customers contact Elvaco AB for the latest 
product information before purchasing a CMi Series product. 
 
The documentation and product are provided on an “as is” basis only and may contain deficiencies or 
inadequacies. Elvaco AB takes no responsibility for damages, liabilities, or other losses by using this 
product. 

1.1 

Copyright and trademark 

© 2022, Elvaco AB. All rights reserved. No part of the contents of this manual may be transmitted or 
reproduced in any form by any means without the written permission of Elvaco AB. Printed in Sweden. 
 
CMi Series is a trademark of Elvaco AB, Sweden. 

1.2 

Contacts 

Elvaco AB  
Kabelgatan 2T 
434 37 Kungsbacka 
SWEDEN 
Phone: +46 300 30250 
E-Mail

[email protected]

  

 
Elvaco AB Technical Support 
Phone: +46 300 434300 
E-Mail: [email protected] 
 
Online

http://www.elvaco.com

 

 

 

Summary of Contents for 1100441







































Reviews: