AAM 58 B / C / F PROFINET
INSTALLATION
INSTRUCTIONS
© Copyright 2020 Eltra S.p.a. Unipersonale. All rights reserved.
All informations in this catalog are subject to change without notice.
Eltra takes no responsibility for typographic errors. For the terms of sales please check the website www.eltra.it.
CONNECTIONS
Connector
Pin
Function
PORT 1
connector
1
Tx D+
2
Rx D+
3
Tx D-
4
Rx D-
POWER
connector
1
+V DC
2
/
3
0 V
4
/
PORT 2
connector
1
Tx D+
2
Rx D+
3
Tx D-
4
Rx D-
CONNECTORS
Complete documentation available on www.eltra.it
This device must be supplied by a Class 2
Power source or Limited Voltage / Current Circuit
Input Voltage: + 30V DC max
Input Current: 0.5A max
SAFETY ADVICES
• The transducer must be used in observance of its specifi cations. The transducer is a precision
measuring instrument and it is not a safety device.
• The personnel charges in mounting and commissioning of the device must be qualifi ed and carefully
follow installation instructions. It is strongly recommended to avoid any mechanical or electrical
modifi cation for safety reasons. The warranty will lose in case of any modifi cations.
• Don’t expose the device to stresses or impacts in order to ensure the correct functioning.
• Make sure that the mechanical coupling of the transducer shaft is designed with the appropriate
elastic couplings, especially in the case of excessive axial or radial movements.
• The mechanical coupling between motor and trasducer shaft has to be made with appropriate elastic
couplings, especially in the case of excessive axial or radial movements.
• Check the operating environment is free from corrosive agents (acids, etc.) or substances that are not
compatible with the device and with its IP rating.
• Check the connection of the device to the ground; if necessary, provide an additional external
connection.
• Products with variant code (a number or combination of numbers after “.”) may have different
mechanical, electrical or connections from standard product. Please refer to the additional
documentation.
• Installation and wiring must be performed by trained personnel in a POWER-OFF condition.
• To prevent short-circuits, insulate unused wires at different lengths; do not use unused pins on the
connector.
• Before switching on, verify the voltage range applicable to the device.
• Place power and signal cables in order to avoid capacitive or inductive interferences that may cause
malfunction of the device. Place also transducer cable far from power lines or any other cable with
high noise levels.
• The user who integrates the transducer in his appliance must observe CE regulations and he is
responsible for the CE marking of the end machine/device.
• The malfunctions due to failure to observe these usage and installation precautions will loose the
warranty.
• Eltra considers itself free from any liability for damages or injuries due to non-observance of these
directives.
1. Apply the elastic coupling
1
on the encoder shaft.
2. Fix the encoder to the customer fi xing fl ange
2
with the n.3 M3 screws
3
.
3. Fix the fi xing fl ange
2
to the motor; please verify the allowed elastic coupling mounting tolerances.
1. Apply the elastic coupling
1
on the encoder shaft.
2. Fix the encoder to the customer fi xing fl ange
2
with the screw
3
.
3. Fix the fi xing fl ange
2
to the motor; please verify the allowed elastic coupling mounting tolerances.
1. Apply the elastic coupling
1
on the encoder shaft.
2. Fix the encoder to the customer fi xing fl ange
2
with the n.3 M4 screws
3
or with n.3 fi xing clamps
4
.
3. Fix the fi xing fl ange
2
to the motor; please verify the allowed elastic coupling mounting tolerances.
1. Apply the shaft adapter
1
(if present) to the encoder shaft and then to the customer motor shaft.
2. Apply the spring on the encoder with n.3 M3x4 supplied screws (recommeded threadlocker
Loctite 243), fi xing torque 0,4 Nm / 57 Ozin recommended.
3. Apply the encoder shaft on the motor shaft.
4. Fix the spring
2
to the customer motor fl ange without fi xing it with n.2 M3 screws
3
.
5. Fix the collar clamping
4
with an HEX key 2,5, fi xing torque 1,5 Nm / 212 Ozin recommended.
6. Fix the spring.
POWER connector (4 pin)
M12 A coded
solder side view FV
PORT 1 / 2 connector (4 pin)
M12 D coded
solder side view MV
* not included
** not included, see P/N 94080001
Led label
Colour
Functionality description
LINK 1
orange and green (blinking)
Link to bus active - incoming and outgoing
activity on PORT 1
LINK 2
orange and green (blinking)
Link to bus active - incoming and outgoing
activity on PORT 2
Error
(red led)
Power
(green led)
Meaning
Cause
Off
Off
No power
Off
On
Data exchange, slave and operation ok
On
On
No connection to another device
Criteria: no data exchange
- Bus disconnected
- Master not available / switched off
Blinking (1)
On
Parameterization fault, no Data
exchange
Criteria: data exchange correct.
However, the slave did not switch to the
data exchange mode
- Slave not confi gured yet (or wrong
confi guration)
- Wrong station address assigned (but not
outside the permitted range)
- Actual confi guration of the slave differs from
the nominal confi guration
(1) Blinking frequency 0,5 Hz, minimal indication time is 3 s
DIAGNOSTIC LEDS
200921
Eltra S.p.a. Unipersonale
36040 Sarego - Italy tel. +39 0444 436489 fax. +39 0444 835335
www.eltra.it [email protected]
cod.29050037
58 C
58 B
1*
2*
4**
3*
1*
3*
2*
1*
2*
3*
58 C
58 F
4
1
2
3*
