ELTEX WB-2P-LR5 User Manual Download Page 40 | Manualshive

Page: 40 / 74

background image

WB-2P-LR5. User manual

40

•
•

5.2.3 The «LAN» submenu

In LAN settings section you may configure local network, DHCP server, set static addresses bindings.

The device is capable to assign IP addresses and other parameters required to the Internet access to computers
connected to LAN interface through DHCP (Dynamic Host Configuration Protocol). The use of DHCP allows to
avoid manual configuration of TCP/IP.

LAN:

IP address

– IP address of the device in a local network;

Netmask

– subnetmask in local network.

LAN settings are available only in router mode.



«
...
38
39
40
41
42
...
»

Summary of Contents for WB-2P-LR5











































































Reviews:

No comments

Related manuals for WB-2P-LR5

Brand: Qixiang Technology Pages: 11

DWL-AG700AP - AirPlus AG - Wireless Access...

Brand: D-Link Pages: 59

DWL-3260AP - AirPremier - Wireless Access...

Brand: D-Link Pages: 57

Brand: Cambium Pages: 103

Brand: VT Miltope Pages: 32

Brand: TP-Link Pages: 85

WI DRIVE WID11GEN

Brand: Dension Pages: 26

Brand: Linksys Pages: 124

Brand: Arista Pages: 4

WLTMS-110_384041

Brand: Gemtek Systems Pages: 14

Brand: Aerohive Pages: 12

Brand: EnGenius Pages: 2

Brand: Luxul Pages: 8

Brand: Allnet Pages: 137

Brand: Allnet Pages: 140

FRITZ! Powerline 1260E

Brand: AVM Pages: 44

Brand: Nanometrics Pages: 4

Brand: AirLive Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands