background image

www.elt.es

4

1. INTRODUCTION

Thank  you  for  choosing  control  gear  for  LED  modules  designed  and  manufactured  by  ELT  (Especialidades 

Luminotécnicas S.A.U.). This user guide will help you learn about iLC CORE driver technology and configure your 

control gear so that it can be correctly integrated into your luminaire.

We advise you to check the latest available version of this document on the ELT website, 

www.elt.es/en.

1.1. Benefits of the technology

The  iLC  CORE  series  is  a  cost-efficient  solution  that  incorporates  multiple  dimming  modes  and  programmable 

functionalities. Given its extensive window of operation, long service life and resilience, the iLC CORE series joins 

the family introduced by our iLC PRO series, enabling you to choose the ideal lighting solution for every light point.

1.2. Classification and symbols

The nomenclature of the iLC CORE control gear, taking an example the 

iLC 58C/350…700-XR

, is described as follows:

 

iLC: Constant current control gear equipped with programmable technology. 

 

58: Maximum output power.

 

C: Symbol for the iLC CORE family.

 

350…700: Constant current output in milliamps in which regulation is permitted.

 

XR: Casing format.

1.3. 

General features of the drivers

The main features of the iLC CORE control gear are:

 

Build-to-use drivers with insulation double or reinforced insulation. IP20 ingress protection. 

 

Suitable for installation in Class I and Class II luminaires.

 

Wide range of input voltages. 

 

High power factor.

 

Low harmonic distortion.

 

Low output ripple current.

 

High quality light without flickering.

 

Programmable by modulating output current size.

 

Wide range of output current regulation.

 

Configurable functionalities for an optimal lighting system design:
- Adjustable output current (AOC).

- LED module constant lumen output (CLO).

 

Different regulation methods can be selected, adapting each lighting point to the needs of the installation:
- 1-10V.

- ActiDIM: stand-alone and dynamic dimming system that adapts to night hours.

- ON/OFF: no regulation.

Summary of Contents for iLC CORE Series






























Reviews: