Elsner 70184 Installation And Adjustment Download Page 7 | Manualshive

Page: 7 / 36

background image

5

Installation and commissioning

Thermo-Hygrometer KNX TH65-AP

• Version: 27.01.2020 • Technical changes and errors excepted.

•

Do not use the device if it is damaged.

•

Take the device or system out of service and secure it against
unintentional use, if it can be assumed, that risk-free operation is no
longer guaranteed.

The device is only to be used for its intended purpose. Any improper modification or
failure to follow the operating instructions voids any and all warranty and guarantee
claims.

After unpacking the device, check it immediately for possible mechanical damage. If it
has been damaged in transport, inform the supplier immediately.

The device may only be used as a fixed-site installation; that means only when assem-
bled and after conclusion of all installation and operational start-up tasks and only in
the surroundings designated for it.

Elsner Elektronik is not liable for any changes in norms and standards which may occur
after publication of these operating instructions.

2.2. Location

The sensor is designed for surface mounting. When selecting an installation location,
please ensure that the measurement results are affected as little as possible by exter-
nal influences. Possible sources of interference include:
•

Direct sunlight

•

Drafts from windows and doors

•

Warming or cooling of the building structure on which the sensor is mounted,
e.g. due to sunlight, heating or cold water pipes

•

Connection lines which lead from warmer or colder areas to the sensor

Temperature variations from such sources of interference must be corrected in the ETS
in order to ensure the specified accuracy of the sensor (temperature offset).

For outdoor installation it must be ensured that a 60 cm gap is left below the sensor in
order to prevent it from being snowed during snowfall.

The sensor must be mounted vertically. The measurement probe and the cable outlet
must point downwards.

2.3. Notes on mounting and commissioning

Do not open the temperature sensor if penetration of water (rain) is likely: Only a cou-
ple of drops could damage the electronic.

Do not dip the measuring tip (metal sleeve with sensor) in water.

Avoid the bedewing of the device. For critical applications, where condensate forma-
tion is expectable, please ask Elsner Elektronik for customized solutions.

«
...
5
6
7
8
9
...
»

Summary of Contents for 70184





































Reviews:

No comments

Related manuals for 70184

Brand: WAGER Pages: 36

Brand: P3 International Pages: 1

Brand: Hanna Instruments Pages: 2

Brand: Vanguard Instruments Company Pages: 111

Brand: Eddyfi Technologies Pages: 72

Brand: STM Pages: 31

Brand: Niigata seiki Pages: 2

Brand: Easy-Laser Pages: 86

Brand: Jacob Jensen Pages: 24

Brand: IME Pages: 14

Brand: Roland Pages: 23

Brand: Mahr Pages: 56

Brand: Stageline Pages: 30

Brand: banjira Pages: 2

Brand: METREL Pages: 29

Bullhorn RM4200 Series

Brand: American Innovations Pages: 68

Brand: KUSSMAUL Pages: 7

DULCODOS universal mini

Brand: ProMinent Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands