Radio dimmer RF-L-DST 1-10 V
1
Radio dimmer RF-L-DST 1-10 V
• Version: 16.05.2022 • Technical changes and errors excepted. • Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany • www.elsner-elektronik.de •
Technical Service: +49 (0) 7033 / 30945-250
EN
RF-L-DST 1-10 V
Radio Dimmer
Technical specifications and installation instructions
Item number 60561
1.
Description
The
RF-L-DST 1-10 V
is a wireless dimmer for the Elsner RF wireless control pro-
tocol. The
RF-L-DST 1-10 V
has a 230 V switch output (16 A) and a 1-10 V control
output for dimming. With this the
Radio dimmer RF-L-DST 1-10 V
is specially de-
signed for the connection of electronic enhanced voltage generators (EVG), LED
converters or electronic power supplies for low voltage systems.
The lighting connected to the wireless dimmer can be controlled automatically and
manually via the WS1 or (KNX) WS1000 Color Style building controller or the
Solexa II wireless control system. Alternatively, direct manual operation is possible
using the Remo 8/pro wireless remote control, via the RF-B2-UP button interface or
the Corlo P RF solar wireless control button.
Functions:
•
Dimmer for an electronic ballast, LED converter or electronic power supply
unit for low-voltage systems
•
230 V switched output, 16 A
•
1-10 V control output
•
Reception of the control signal via radio
•
Suitable for: WS1 Color, WS1 Style, WS1000 Color, WS1000 Style, KNX
WS1000 Style (each from software version 1.818), Solexa II, Remo 8 (from
version 0.1), Remo pro, RF-B2-UP, Corlo P1 RF, Corlo P2 RF
1.1. Deliverables
•
Radio dimmer
•
STASI locking bow, rubber seals
Available accessories:
•
Mains connection wire (5 m)
•
Connection wire (available in 1 m; 2,5 m; 5 m)
1.2. Technical data
The device is designed according to the criteria for safety extra-low voltage (SELV).
If the 1-10 V control output is to meet the SELV criteria, all connected luminaires and
ballasts must also meet the SELV requirements.
*The
Radio dimmer RF-L-DST 1-10 V
should be installed in a protected area de-
spite a high degree of protection because water can enter in via the connectors.
Please observe the instructions in Chapter
Connection
.
The product conforms with the provisions of EU directives.
1.2.1. Illumination brightness (dimming behaviour)
For the Elsner controls, 10 V are specified with 100% dimming brightness (maxi-
mum brightness) and 1 V with 10% dimming brightness. How bright the minimum
illumination at 1 V actually is and how the brightness changes between 1 and 10 V
depends on the connected lighting system.
2.
Installation and start-up
Installation, testing, operational start-up and troubleshooting should
only be performed by an authorised electrician.
DANGER!
Risk to life from live voltage (mains voltage)!
There are unprotected live components inside the device.
• Inspect the device for damage before installation. Only put undamaged
devices into operation.
• Comply with the locally applicable directives, regulations and provisions for
electrical installation.
• Immediately take the device or system out of service and secure it against
unintentional switch-on if risk-free operation is no longer guaranteed.
Use the device exclusively for building automation and observe the operating inst-
ructions. Improper use, modifications to the device or failure to observe the opera-
ting instructions will invalidate any warranty or guarantee claims.
Operate the device only as a fixed-site installation, i.e. only in assembled condition
and after conclusion of all installation and operational start-up tasks, and only in the
surroundings designated for it.
Elsner Elektronik is not liable for any changes in norms and standards which may
occur after publication of these operating instructions.
2.1. Notes on wireless equipment
When planning facilities with devices that communicate via radio, adequate radio
reception must be guaranteed. The range of wireless control will be limited by legal
regulation and structural circumstances. Avoid sources of interference and obsta-
cles between receiver and transmitter, that could disturb the wireless communica-
tion. Those would be for example:
•
Walls and ceilings (especially concrete and solar protection glazing).
•
Metal surfaces next to the wireless participants (e. g. aluminium construction
of a conservatory).
•
Other wireless devices and powerful local transmitters (e.g. wireless
headphones), which transmit on the same frequency. Please maintain a
minimum distance of 30 cm between wireless transmitters for that reason.
2.2. Installation and connection
The radio module is connected between the appliance and the power supply. It may
only be connected to flexible lines using STAK/STAS connectors. The connectors
must be locked using the locking bow. Use the provided rubber seals between the
STAK/STAS connectors. The connectors must be locked using the STASI locking
bow.
Do not expose to continuous sun radiation
to avoid overheating.
The housing is not UV-resistant.
No water may run along the supply line and device.
The device must not be exposed to water (rain). This could result in the
electronic being damaged. A relative air humidity of 95% must not be
exceeded. Avoid bedewing.
•
Assembly the device in a protected area (e. g. in
the box for the blinds/marquee/shutters in a construction
profile beneath the roof tiles or in a housing).
•
Lay the supply lines out and down from the device.
No vibrations!
•
Assemble the device in a place that is free of vibrations.
Housing
Plastic
Degree of protection
IP 53*
Dimensions
approx. 149 x 72 x 29 (W x H x D, mm)
Weight
approx. 180 g
Ambient temperature
Operation -20…+55°C, storage -30…+85°C
Ambient humidity
max. 95% RH, avoid condensation
Operating voltage
230 V AC, 50 Hz (STAS3 plug)
Output
1 x switched output 230 V, 16 A, STAK3 coupling
1 × dimming 1-10 V, maximum 100 mA, STAK3 coupling
Radio frequency
868.2 MHz (Elsner RF)
The antenna symbol on the housing shows the positi-
on of the antenna in the device. This side must not be
positioned directly on metal surfaces or objects. Other-
wise, the radio signal might disturbed.
Metal
profile
R
F
-
L
