background image

13

Parameter settings

Temperature Sensor KNX T-UN

 • Version: 27.01.2020 • Technical changes and errors excepted.

Block

The switching output can be blocked using an object. Define specifications here for the
behaviour of the output when blocked.

The behaviour of the switching output on release is dependent on the value of the pa-
rameter "Switching output sends" (see "Switching output")

5.5.

Temperature PI controller

Activate the controller if required.

General control

Then define the type of setting. Heating and/or cooling may be controlled in two stages.

Use temperature switching output block

No • Yes

Analysis of the temperature blocking object

• At value 1: block | At value 0: release 
• At value 0: block | At value 1: release

Value of the temperature blocking object
before first call 

0 • 1

Behaviour of the switching output

On block

• Do not send message 
• send 0 
• send 1

On release
(with 2 seconds release delay)

[Dependent on the "Switching output 
sends" setting]

Switching output sends on change

• Do not send message 
• Send switching output status

Switching output sends on change to 1

• Do not send message 
• if switching output = 1 

 send 1

Switching output sends on change to 0

• Do not send message
• if switching output = 0 

 send 0

Switching output sends on change and 
periodically

Send switching output status

Switching output sends on change to 1 and 
periodically

if switching output = 1 

 send 1

Switching output sends on change to 0 and 
periodically

• if switching output = 0 

 send 0

Use controller

Yes • No

Type of control

• Single stage heating
• Dual-stage heating
• Single-stage cooling
• Single-stage h single-stage cooling
• Dual-stage h single-stage cooling
• Dual-stage h dual-stage cooling

Summary of Contents for KNX T-UN 130



























Reviews: