background image

6

|

 

www.gd-elmorietschle.com

 © Gardner Denver Schopfheim GmbH, Gardner Denver Deutschland GmbH

Safety

2 Safety

The manufacturer is not responsible for damage if 
you do not follow all of this documentation.

2.1 

Warning instruction markings

Warning

Danger level

Consequences if not obeyed

DANGER

immediately imminent danger 

Death, severe bodily injury

WARNING

possible imminent danger

Death, severe bodily injury

CAUTION

possible hazardous situation

Slight bodily injury

NOTICE

possible hazardous situation

Material damage

2.2 General

These operating instructions contain basic instruc-
tions for installation, commissioning, maintenance 
and inspection work which must be obeyed to en-
sure the safe operation of the machine and prevent 
physical and material damage.
The safety instructions in all sections must be taken 
into consideration.
The operating instructions must be read by the 
responsible technical personnel/ operator before 
installing and commissioning and must be fully un-
derstood. The contents of the operating instructions 
must always be available on site for the technical 
personnel / operator.  Instructions  fi xed directly onto 
the machine must be obeyed and must always re-
main legible. This applies for example to:

 

• 

Symbols for connections

 

• 

Data and motor data plate

 

• 

Instruction and warning plates

The operator is responsible for observing local regu-
lations.

Summary of Contents for C-KLR 140































Reviews: