background image

 

III.  S

YSTEM 

C

OMPONENT 

D

ESCRIPTIONS

 

 

8294-07 Scorpion RF Monitors 

(Figure 4) The 8294-06 Scorpion is a cast aluminum monitor 
with  4"  waterway.    The waterway  contains  a  central  vane  to 
minimize  large-scale  turbulence  and  provide  superior  fire 
streams.  Monitor water supply connection is a 4 inch 150 lb. 
ANSI  pattern  flange.    The discharge  nozzle  connection  is  3-
1/2  inch  National  Hose  thread.    Nozzle  stream  direction  is 
controlled  by  two  permanent  magnet  type  planetary  gear 
motors,  one  controlling  rotation  about  the  axis  of  the  water 
inlet,  and  the  other  controlling  nozzle  elevation  and 
depression.    Right  angle  gear  cases  between  the  gear  motor 
and the monitor allow for convenient manual override of the 
electric  motors  in  the  event  of  a  power  failure  during 
firefighting  operations.    All  gearing  is  enclosed  within  the 
monitor housings.   
 
The  maximum  monitor  flow  capacity  is  2000  gallons  per 
minute.    Monitors  can  be  supplied  with  the  SM-1250E 

 constant pressure (automatic) type master stream 

nozzle.  This nozzle has a flow range of 300 to 1250 gallons 
per minute at 75 psi and has an electric drive mechanism for 
RF control of the spray pattern from a straight stream to wide 
fog.  A similar nozzle, the SM-2000E, provides a flow range 
of  500  to  2000  gallons  per  minute  at  80  psi.    For  optimum 
straight  stream  performance,  stream  shapers  are  provided  as 
part of the monitor and nozzle system.  Solid stream nozzles 
are also available for use with these monitors. 

 

Figure 4  

8294-06 Monitor with 284-A and SM-

2000E 

 

A.

 

RF Receiver/Control Module 

The monitor control circuit uses a state-of-the-art PIC (Programmable Integrated Circuit) chip design.  
This device allows numerous control features while keeping circuit board size to a minimum.  Relays 
within this box provide motor reversing control for the Up/Down, Left/Right and Straight Stream/Fog 
functions.   
 
All functions are sent to the RF Receiver/Control Module via an encoded radio frequency link.  The 
radio  link  reduces  the  number  of  control  wires  down  to  just  the  two  power  leads,  dramatically 
simplifying the installation procedure.  The link also allows wireless control up to ¼ mile away using a 
battery powered handheld transmitter. 
 

Summary of Contents for Scorpion RF 8294-07

























Reviews: