U.S. Patent No. D403,750
Patente estadounidense D403,750
Brevet U.S.A. no. D403,750
FINISHED WALL
PARED TERMINADA
MUR FINI
4"
4" (102 MM)
102 mm (4 po.)
TOP OF TUB RIM
BORDE SUPERIOR DE LA BAÑERA
HAUT DE REBORD DE BAIGNOIRE
BOTTOM OF TUB
FONDO DE LA BAÑERA
FOND DE BAIGNOIRE
74" FOR HEAD CLEARANCE
74" (188 CM) DE ALTURA
188 cm (74 po.) POUR DÉGAGER LA TÊTE
4" REF.
4" (102 MM) REF.
RÉF. 102 mm (4 po.)
1-5/8" TO 3-1/4"
1-5/8" A 3-1/4" (41 MM A 83 MM)
41 mm (1-5/8 po.) À 83 mm (3-1/4 po.)
18" OPTIONAL
18" (45,7 CM) OPTATIVO
OPTION 45,7 cm (18 po.)
*5-1/8" REF.
5-1/8" (130 MM) REF.
RÉF. 130 mm (5-1/8 po.)
*FOR COPPER SWEAT
OR SLIP-ON ONLY
1/2" NPT
1/2" (12,7 MM) NPT
12,7 mm (1/2 po.) NPT
1/2" COPPER
1/2" (12,7 MM) COBRE
CUIVRE 12,7 mm (1/2 po.)
6"
6" (152 MM)
152 mm (6po.)
1" REF.
1" (25 MM) REF.
REF. 25 mm (1 po.)
5-1/2" REF.
5-1/2" (140 MM) REF.
RÉF. 140 mm (5-1/2 po.)
OPTIONAL TO FINISHED
FLOOR USUALLYBETWEEN 65'' AND 78'
'
"SEE ILLUSTRATION "
VEA LA FIGURA INFERIOR
VOIR INSTALLATION CI-DESSOUS
Por favor lea estas instrucciones detenidamente antes de
comenzar para que lleve a cabo la instalación sin contratiempos.
Pour vous assurer que l’installation se déroulera sans difficulté,
veuillez lire attentivement ces instructions avant de commencer.
To ensure that your installation proceeds
smoothly--please read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1
Cumplimiento certificado de los requisitos
de la norma ANSI A112.18.1
Certifié conforme à ANSI A112.18.1
ROUGHING-IN DIMENSIONS
Instrucciones de instalación
Installation Instructions
To assure proper positioning in relation to wall,
note roughing-in dimensions.
Tome nota de las dimensiones de desbastado para
asegurar la posición correcta respecto de la pared.
Pour garantir un bon positionnement par rapport au
mur, tenir compte des dimensions de préparation.
DIMENSIONES DE DESBASTADO
DIMENSIONS DE PRÉPARATION
STRATTON
9315.502
HABITUELLEMENT ENTRE
165 cm (65 po.)
ET 198 cm (78 po.)
ENTRE OPTION ET PLANCHER FINI
OPTATIVO AL PISO TERMINADO,
POR LO GENERAL ENTRE
65" Y 78" (165 A 198 CM)
'
M965008 REV.1.1
ASSISTANCE TÉLÉPHONIQUE
NUMBERO DE EMERGENCIA
HOTLINE FOR HELP
For toll-free information and answers to your questions, call:
Para información y respuestas a sus preguntas, llame sin costo al:
Pour information et réponses à vos questions, composer sans frais:
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
© A S A m e r i c a , I n c . 2 0 0 8
1 800 442-1902
Weekdays Días laborales de las Sur semaine:
8:00 to 6:00 p.m. EST
CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays Días laborales de las Sur semaine:
8:00 to 7:00 p.m. EST
0 1 2 3
4
5
6
H
C
PRESSURE BALANCING BATH AND SHOWER SET
JUEGO DE MOLDURA PARA BAÑO Y DUCHA
BAIN et DOUCHE
ENTRÉES
4 1/16 PO
4 1/16 PO
2 PO
1
ROUGHING-IN
Turn off water at main supply.
CAUTION
When soldering, remove PLASTER GUARD, CARTRIDGES and CHECK STOPS (IF PRESENT). When finished soldering,
flush valve body, replace cartridges, check stops (if present) and plaster guard to continue installation. Use thread
sealant or Teflon tape on threaded connections.
NOTE
If the valve is installed on a fiberglass or other thin wall
application, the PLASTER GUARD
(4)
can be used as a support.
See Roughing-in diagram before starting.
Connect RISER PIPE
(1)
to MANIFOLD
(2)
top
outlet marked "SHR".
Connect TUB FILLER PIPE
(3)
at bottom
outlet marked "TUB".
Supply connections are:
1/2" female NPT for threaded inlets
For proper positioning the finished wall
must be within side wall of PLASTER
GUARD
(4)
.
Connect hot and cold water supplies.
Cap off shower pipe
(5)
and tub filler pipe
(6)
.
For support, use pipe BRACES
(7)
secured to wooden braces.
With valve turned off, turn on water supplies. Check for leaks.
COLD
HOT
Cut a 3" dia. hole in the shower stall.
Remove PLASTER GUARD
(4)
, rotate 90 degrees
so that indicated screw holes fit MANIFOLD
(2)
.
Push CAP on valve, place ESCUTCHEON on and attach
with screws.
1
7
5
3
6
4
2
SHR. 1/2" NOM.
COPPER SWEAT
'
DUCHA, 1/2" (12,7 MM)
NOM. COBRE SOLDADO
'
CUIVRE LISSE 12,7 mm
(1/2 po.)NOM. DOUCHE
SHR. 1/2" NOM.
COPPER SWEAT
'
DUCHA, 1/2" (12,7 MM)
NOM. COBRE SOLDADO
'
CUIVRE LISSE 12,7 mm
(1/2 po.)NOM. DOUCHE
SWEAT INLETS
ENTRADAS SOLDADAS
ENTRÉES LISSES
Consignes d’installation
