Elite Fitness SECA3 Assembly Manual Download Page 11 | Manualshive

Page: 11 / 26

background image

11

ELITE ELLIPTICAL ASSEMBLY MANUAL

ASSEMBLY INSTRUCTIONS

STEP 7

—

Connect Upper Computer Wire from Computer (#1) to the Front Post Wire (#13).

—

Connect Upper Pulse Wire from Computer (#1) to the Lower Pulse Wire from Handlebar.

—

Attach Computer (#1) to the Front Post (#10) using 4 x M5 Screws (#5). Screws are pre-

assembled in computer. Refer to the above diagram.

—

Attach the front Computer Cover (#14F) using 1 x M5 screw (#12)

—

Attach the rear Computer Cover (14R) using 2 x M5 screws (#12) and 2 x Self Taping Screws

(#10).

«
...
9
10
11
12
13
...
»

Summary of Contents for SECA3



























Reviews:

No comments

Related manuals for SECA3

Brand: Daavlin Pages: 13

Brand: Daavlin Pages: 27

Brand: Keithley Pages: 32

Brand: jcb Pages: 166

BOMAG BW 100 ADM-5

Brand: Fayat Pages: 216

Brand: B medical systems Pages: 28

Brand: jablotron Pages: 2

Brand: jablotron Pages: 2

Brand: Parkside Pages: 95

Brand: Yamaha Pages: 45

Brand: Jäger Pages: 36

Brand: IMG STAGE LINE Pages: 12

Brand: Ametek Pages: 20

L10 LVELED Series

Brand: Clevetronics Pages: 2

Brand: Goobay Pages: 20

Alcotest 7410 GLC

Brand: Dräger Pages: 15

Brand: enz Pages: 40

Be strong NS 200X

Brand: Nautilus Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands