elho V-Twin 750 S Series Manual Download Page 5

5

4

5

4

LIMITED WARRANTY

This Limited Warranty is a product warranty given by Oy El-Ho Ab (“ELHO”) warranting the 

quality of its manufactured products to the original owner. ELHO´s liability for defects in the 

manufactured products is limited as stated in the conditions below. 

1. Warranty extent and period 

ELHO warrants that new machinery and equipment manufactured by ELHO will be 

free from defects in material and workmanship under normal use for a period of twelve 

(12) months after the date of sale to the original owner (“the Customer”) and under the 

condition that the Distributor has registered the warranty at ELHO by returning the Warranty 

Registration Form within 14 days from the date of sale to the Customer (“the Limited 

Warranty”). 

A repair under this Limited Warranty does not extend the warranty period. 

2. Warranty claim 

Any claim under the Limited Warranty shall be reported by returning a complete Warranty 

Application to ELHO within 14 days from the date when the Customer made the Distributor 

aware of the defect; or else the warranty claim will not be accepted. A complete Warranty 

Application shall in any case be sent to ELHO within 30 days from the date when the damage 

was discovered or should reasonably have been discovered; or else the warranty claim will 

not be accepted. The Distributor shall prove that the Warranty Application was sent within the 

time limits stated above. 

3. Repair or replacement procedure 

Under the conditions that the warranty has been correctly registered according to clause 

1 and the warranty claim has been made in compliance with clause 2, ELHO assumes 

responsibility under the Limited Warranty to, at ELHO’s option, repair or replace all parts 

that in ELHO’s opinion are defected in material or workmanship. This responsibility can be 

satisfied  by  shipping  the  parts  needed  for  repair  or  replacement  to  the  Distributor.  ELHO 

assumes responsibility for the costs of spare parts needed for repair or replacement and for 

the freight of these parts to the Distributor. 

The Distributor shall maintain the defective parts for six (6) months after their replacement. 

On ELHO’s initiative and at its expense, the defective parts shall be shipped to ELHO for 

analysis. 

4. Limitations on warranty coverage 
4.1 Components not manufactured by ELHO 

Components not manufactured by ELHO, but incorporated in machinery and equipment 

manufactured by ELHO, e.g. hydraulic components, power transmission shafts, gearboxes, 

tires etc., are covered by the warranty granted by the original manufacturer of the components. 

4.2 No warrant for fitness or performance 

ELHO does not warrant the fitness of the machinery or equipment for a particular purpose or 

the performance of the machinery or equipment. 

4.3 Damage caused by the owner 

The Limited Warranty does not cover damage or loss that in ELHO’s opinion is resulting from 

normal wear and tear or damage or loss resulting from misuse, overload, accident, neglect 

or improper installation, operation or maintenance, alteration of the machinery or equipment 

without ELHO’s written consent or usage of non-original parts. Agricultural machinery is 

subjected to wear and tear and needs regular maintenance. 

Summary of Contents for V-Twin 750 S Series








































Reviews: