Elevation DYNAMIC INUQUE Owner'S Operation And Maintenance Manual Download Page 30

Rev. 0

Rev. 0

page

 30

page

 3

1  SPECIAL NOTES

WARNING/CAUTION — notices as used in this manual apply to hazards or unsafe practices which could 

result in personal injury or property damage.

NOTE — THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. 

An updated version of this owner’s manual may be available at www.PDGMobility.com

INDICATIONS FOR USE — To provide mobility to persons limited to a seated position.
WHEELCHAIR USER — As a manufacturer of wheelchairs, PDG endeavors to supply wheelchairs to meet 

many needs of the end user. However, final selection of the type of wheelchair to be used by an 
individual rests solely with the user and his/her health care professional capable of making such a 
selection.

WHEELCHAIR TIE-DOWN RESTRAINTS AND SEAT RESTRAINTS — Wheelchair users are NOT to be 

transported in vehicles of any kind while in wheelchairs. As of this date, Transport Canada, and the 
Department of Transportation has not approved any tie-down systems for transportation of a user in 
a moving vehicle of any type while in a wheelchair.

 

It is PDG’s position that users of wheelchairs should be transferred into appropriate seating in vehicles 
for transportation and that use be made of the restraints made available by the auto industry. PDG 
can not and does not recommend any specific wheelchair transportation systems.

POSTURAL SUPPORT DEVICE or LAP BELT

 — 

IT IS THE OBLIGATION OF THE HME DEALER, THERAPISTS 

AND OTHER HEALTH CARE PROFESSIONALS TO DETERMINE IF A POSTURAL SUPPORT DEVICE IS REQUIRED 
TO ENSURE THE SAFE OPERATION OF THIS EQUIPMENT BY THE USER. SERIOUS INJURY CAN OCCUR IN THE 
EVENT OF A FALL FROM A WHEELCHAIR.

2  SAFETY SUMMARY

Operating Information Warning

To determine and establish particular safety limits, practice bending, reaching and transferring activities 
in several combinations in the presence of a qualified health professional BEFORE attempting active use 
of the wheelchair.

6

  DO NOT attempt to reach objects if you have to move forward in the seat.

6

  DO NOT attempt to reach objects if you have to pick them up from the floor by reaching down 

between your knees.

6

  DO NOT lean over the top of the back upholstery to reach objects from behind as this may cause the 

wheel chair to tip over.

6

  DO NOT shift your weight or sitting position toward the direction you are reaching as the wheelchair 

may tip over.

6

  DO NOT use an escalator to move a wheelchair between floors. Serious bodily injury may occur.

6

  DO NOT attempt to stop a moving wheelchair with the wheel locks. WHEEL LOCKS ARE NOT BRAKES.

4

  Before attempting to transfer in or out of the wheelchair, every precaution should be taken to reduce 

the gap distance. Turn both casters toward the object you are transferring onto. When transferring to 
and from the wheelchair, ALWAYS ENGAGE BOTH WHEEL LOCKS.

22  ISO TEST INFORMATION DISCLOSURE

Table 22.1

  Elevation Wheelchair Test Configuration

Seat Width

457 mm (18 in)

Seat Depth

407 mm (16 in)

Seat Back Height

240 mm (9.45 in)

Wheelchair Weight

12 kg (26.5 lbs)

Seat sling

Standard Sling Seat w/tension straps

Back Upholstery

Standard back upholstery

Wheels

24” Wire Wheels

Casters

5” Aluminum Soft Roll

Footrest

Aluminum Footrest

Other Options

None

Mass of ATD

115 kg (250 lbs)

Max. User Weight

115 kg (250 lbs)

Table 22.2

  Dimensional and Performance Attributes

Feature

Minimum

Maximum

Overall length with legrest

815 mm (32 in)

876 mm (34.5 in)

Overall width

587 mm (23.1 in)

688 mm (27.1 in)

Total mass

12.0 kg (26.5 lbs)

12.0 kg (26.5 lbs)

Static stability downhill

>10°

>10°

Static stability uphill

5.4°

7.6°

Static stability sideways

>10°

>10°

Seat plane angle

12.0°

n/a

Effective seat depth

356 mm (14 in)

457 mm (18 in)

Effective seat width

356 mm (14 in)

457 mm (18 in)

Seat surface height at front edge

485 mm (19.1 in)

515 mm (20.3 in)

Backrest angle

-14.5°

+48.0°

Backrest height

240 mm (9.4 in)

370 mm (14.6 in)

Footrest to seat distance

385 mm (15.2 in)

425 mm (16.7 in)

Leg to seat angle

60º

100º

Hand-rim diameter

520 mm (20.5 in)

572 mm (22.5 in)

Minimum turning radius

515 mm (20.3 in)

515 mm (20.3 in)

The Elevation wheelchair conforms to the test methods for static, impact and fatigue strengths as 
required by ISO 7176-8.

SAVE THIS MANUAL FOR FUTURE REFERENCE

Summary of Contents for DYNAMIC INUQUE

































Reviews: