Eletech LanConn-400 User Manual Download Page 2

Page: 2 / 13

LanConn-400 User’s Guide

1. Description

LanConn-400 is a full duplex serial port to Ethernet converter. Through LanConn-400, your system

can easily communicate with the LAN, WAN or Internet via the RS232/RS422/RS485 port. When

sending data to the network, LanConn-400 automatically adds the necessary TCP/IP stack. When

receiving data from the network, LanConn-400 automatically removes the TCP/IP stack.

LanConn-400 also provides a device interface with 4 serial ports and 1 keyboard port, making it a

powerful and cost effective solution to many applications such as industrial automation and remote

(Internet enabled) device control.

2. System Structure

3. Specifications

Hardware

Samsumg S3C4500A ARM7 CPU, 25 MHz

2MB DRAM

128 KB Flash ROM

Realtek 8201BL Ethernet PHY

Protocol

ARP, IP, UDP, TCP, ICMP, HTTP, DHCP

Interface

10/100 Mbps

300 – 230400 bps asynchronous stream 1

RS232/RS422/RS485, 3 RS232 only

1 Keyboard port, PS2 type, 3 RS232 only

Throughput

23 KB/s per-channel, full-duplex

ARM7 CPU + MAC

1M X 16 DRAM

128K X 8 Flash ROM

Ethernet PHY

MII

100/10 Mbps

RS232/RS422/RS485

RS232

Keyboard

Summary of Contents for LanConn-400













Search results

Summary of Contents for LanConn-400

Reviews:

Brands by name

Popular brands

Eletech LanConn-400, User Manual

Search results

Summary of Contents for LanConn-400

Reviews:

Brands by name

Popular brands