6
Travel profiles
The RolMotion M-868 drive has the two travel profiles
default mode and whisper mode.
Default mode
Whisper mode
Travels at high speed
except before the end
positions. The roller blind
slats are lowered slowly.
Travel the full path at a
reduced speed
Activation in down direction
of travel:
•
Briefly press the [
DOWN/
CLOSE
▼]
button:
Travel to lower end
position.
When placing the blind
slats onto the end
position, the speed is
reduced.
Activation in down direction
of travel:
• Press the [
DOWN/
CLOSE
▼]
button for
about 3 seconds:
Travel
at reduced speed to
lower end position.
• Double click the [
DOWN/
CLOSE
▼] button: The
blind travels to the saved
intermediate position
(if this is not defined,
travel to the lower end
position).
Activation in up direction of
travel:
•
Briefly press the [
UP
▲]
button:
Travel to upper
end position.
Activation in up direction of
travel:
• Press the [
UP
▲] button
for
approx. 3 seconds:
Travel at reduced speed
to the upper end position
• Double click the [
UP
▲]
button: The blind travels
to the saved ventilation
position (if this is not
defined, travel to the
upper end position).
Switching to travel profile
whisper mode:
•
Press the travel button
for approx. 3 seconds
in the same direction as
the current direction of
travel.
Switching to travel profile
default mode:
•
Press the travel button
briefly
in the same
direction as the current
direction of travel.
The drive responds to
the timer functions of
programmed controllers
(TempoTel 2, AstroTec,
MultiTec Touch, Centero
Home).
The drive responds
to commands from
programmed sensors:
•
Sun sensor: Travel to
intermediate position or
lower end position.
The travel profile whisper mode is not available during the
„Setting the end positions“ operation.
7
Troubleshooting
Problem / Error Possible cause Remedial
action
• Drive stops
during travel
• End positions
are not set
• Drive is in
setting mode
• Setting end
positions: First
program the
upper end
position, then
the lower end
position.
8 | EN
©
elero
GmbH
Transmitter programming | Travel profiles
Programming additional transmitters
Operating procedure
Result
3
On the
(additional)
transmitter to be program
med,
press the [
UP
▲]
button immediately (within
1 second) after the blind
starts moving upwards.
The status display
lights briefly. The blind
stops briefly, starts
moving again and then
moves downwards.
4
On the (additional)
transmitter to be program
med,
press the [
DOWN/
CLOSE
▼] button
immediately (within 1
second) after the blind
starts moving downwards.
The status display
lights briefly. The drive
will stop.
The additional transmitter is programmed.
Stop bidirectional wireless mode:
Hold down the [
STOP ■
] button for at least 6 seconds until
the status display lights up (depends on transmitter).
5.8 Deleting the radio connection between
ransmitters and receivers
Refer to the respective instructions for the transmitter.
5.9 Programming or deleting further blind
positions
• Intermediate position: Blind at any position between
upper and lower end position.
Defining the
interim position
in the receiver
Approaching
the intermediate
position
Deleting the
intermediate
position
Prerequisite: The blind
is in the upper end
position.
1. Press the [
DOWN/
CLOSE
▼] button
until the desired
intermediate position
is reached.
2. Additionally press the
[
STOP
■
] button
.
The blind will stop.
The status LED lights
up briefly.
The intermediate
position is now stored.
Prerequisite: The
intermediate position is
defined.
• Double click the
[
DOWN/CLOSE
▼]
button twice (in quick
succession): Blind
moves to the saved
intermediate position.
If no intermediate
position has been
defined, the blind moves
to the lower end position.
If an intermediate
position is to be
controlled for several
receivers simultaneously,
the receivers must be
programmed on one
channel (single channel).
• Hold down
the buttons
[
DOWN/
CLOSE
▼]+
[
STOP
■]
simultaneously
for
approximately
3 seconds.
The intermediate
position is now
deleted. The status
LED lights up briefly.
• Ventilation position:
Ventilation gaps for application of the roller blinds open
Defining the
ventilation
position in the
receiver
Approaching
the ventilation
position
Deleting the
ventilation
position
Prerequisite: The blind
is in the lower end
position.
1. Press the [
UP
▲]
button until the
ventilation gaps
open.
2. Then press the
[
STOP
■
] button
.
The blind will stop.
The position of the
ventilation is now
saved.
Prerequisite: Position
of the ventilation is
defined.
• Double click on the
[
UP
▲] button: The
blind travels upwards
to the saved position.
If no ventilation position
is defined, the blind
moves to the upper
end position.
• Press the [
UP
▲]+[
STOP
■
]
buttons
simultaneously for
approximately 3
seconds.
The position of the
ventilation is now
deleted.
Approach to the intermediate position and the ventilation
position takes place in the whisper mode travel profile
(see Chapter 6).
