5.5.5 Variant C: Fixed upper and lower limit stop
Variant C: Fixed upper and lower limit stop
①
Starting from a central blind position, press the
[
UP
▲] button with the assembly cable or a
programmed transmitter until the blind has reached the
upper end position (travels to the upper limit stop).
The drive begins to travel, briefly stops and travels
further (for as long as the [
UP
▲] button remains
pressed).
The drive switches off automatically when the upper
limit stop is reached.
②
Press the [
DOWN/CLOSE
▼] button until the drive
stops automatically.
The upper end position has been set.
③
Press the [
DOWN/CLOSE
▼] button again until the
blind has reached the desired end position (travels
to the lower limit stop).
The drive begins to travel, briefly stops and travels
further (for as long as the [
DOWN/CLOSE
▼] button
remains pressed).
The drive switches off automatically when the lower
limit stop is reached.
④
Press the [
UP
▲] button until the drive stops
automatically.
By default, the lower end position has been set.
Non-standard setting for placement of the blind slats
at the lower end position: See chapter 5.6.
Adjustment of the variant C end position is complete.
5.5.6 Variant D: Upper end position freely
adjustable, fixed lower limit stop
Variant D: Upper end position freely adjustable,
fixed lower limit stop
①
Starting from a central blind position, press the [
UP
▲] button with the assembly cable or a programmed
transmitter until the blind reaches the desired upper
end position.
The drive begins to travel, briefly stops and travels
further (for as long as the button remains pressed).
You can make corrections using the [UP ▲] and
[DOWN/CLOSE ▼] buttons.
②
Press the [
DOWN/CLOSE
▼] button until the drive
stops automatically.
The upper end position has been set.
③
Press the [
DOWN/CLOSE
▼] button again until the
blind has reached the desired end position (travels
to the lower limit stop).
The drive begins to travel, briefly stops and travels
further (for as long as the [DOWN/CLOSE ▼] button
remains pressed).
The drive switches off automatically when the lower
limit stop is reached.
④
Press the [
UP
▲] button until the drive stops auto
-
matically.
By default, the lower end position has been set.
Non-standard setting for placement of the blind slats
at the lower end position: See chapter 5.6.
Adjustment of the variant D end position is complete.
5.6 Placement of the roller blind slats
For slow lowering of the roller shutter bars, a standard
travel path is set after setting the end positions.
It is possible to change this position when the end positions
have been programmed:
• After the blind starts to rise from the lower end position,
hold down the [
UP
▲] button until the drive starts to move
further up after approx. 2 seconds. As soon as the lowest
blind slat is raised from the lower limit stop, release the
[
UP
▲] button. This is now the position from which slow
downward travel commences.
5.7 Program the transmitter
Important
Precondition: The drive must be in radio operation mode.
►
If the end positions have not been programmed, remove
the blind from the winding shaft.
5.7.1
Programming the first transmitter
Programming the (first) transmitter
Operating procedure
Result
1
Switch the power off and
on again
The drive is in
learning mode for
approximately
5 minutes.
2
Press the programming
button
P
on the transmitter
to be programmed for
approximately 1 second.
The status display
lights up. The drive is
now in learning mode
(up/down travel) for
approximately
2 minutes.
3
Immediately (maximum
1 second) after the start of
upward travel, press the
[
UP
▲] button.
The status display
lights briefly. The blind
stops briefly, starts
moving again and then
moves downwards.
4
Immediately (maximum
1 second) after the start of
downward travel, press the
[
DOWN/CLOSE
▼] button.
The status display
lights briefly. The drive
will stop.
The (first) transmitter is now programmed.
5.7.2 Programming additional transmitters
Up to 16 transmitters can be programmed.
Programming additional transmitters
Operating procedure
Result
1
On an
already programmed
transmitter,
hold down
the buttons [
UP
▲] +
[
DOWN/CLOSE
▼] + [
P
]
(programming button)
simultaneously for
approximately 3 seconds.
The status display
lights up.
The drive is in
learning mode for
approximately
5 minutes.
(alternative to the previous
line)
Switch the power off and
on again
The drive is in
learning mode for
approximately
5 minutes.
2
On the
(additional)
transmitter to be
programmed,
press the
programming button [
P
].
The status display
lights briefly. The drive
is in learning mode
(up/down travel) for
approximately
2 minutes.
©
elero
GmbH
EN | 7
End position settings
