elero RolMotion M-868, Operating And Assembly Instructions Manual

Page: 5 / 12

Ingress of moisture will damage or even destroy the
RolMotion M-868.
► For devices with protection class IP 44, the customer-
side connection of the cable ends or plugs (cable feed-
through) can also be implemented according to protection
class IP 44.
Damage or destruction of the RolMotion M-868 for variants
with 230 V ~ due to incorrect activation.
► Switches with an OFF presetting (dead-man's switches)
for drives are to be attached within visible range of the
RolMotion M-868 but away from spontaneously moving
parts and at a height of more than 1.5 m.
Connect only in de-energised state. To do this, switch
the drive cable so it is de-energised.
1 Press locking mechanism on the motor cable plug
towards the cable using a suitable screwdriver.
2 Pull out the plug.
3 Insert the motor cable plug until the lock engages.
Removing and inserting the motor cable plug
Delivery con-
dition
Removing plug Inserting plug
Fig. 4 Removing and inserting the motor cable plug
5.3 Connection example for RolMotion M-868
230 V / 50 Hz
3
2
1
Fig. 5 Connection diagram RolMotion M-868
230 V / 50 Hz and cable assignment when using
Hirschmann plug connection STAS-3 (with jumper)
Important
The motor controls in the up or down travel directions must
be locked against each other.
A switching time of at least 0.5 seconds must be observed.
5.4 Commissioning
→
1
→
2
→
3
1 Winding thermostat
2 Motor cable plug
3 Junction box
(outside the roller blind case)
4 Electronics
5 Capacitor
bl black
br brown
bl blue
gr/ye
green/yellow
Important
The drive is in commissioning mode when delivered.
► The end positions must be adjusted using the elero
assembly cable (see Fig. 6) or an elero wall or hand-held
transmitter (see Fig. 7).
► The assembly cable may only be connected to
commission the drive and for adjustment operations
5.4.1 Connection for assembly cable
%ODX1HXWUDOOHLWHU
6FKZDU]
%UDXQ
*UQJHOE
HOHUR HOHUR
%OXHQHXWUDOFRQGXFWRU
%ODFN
%URZQ
*UHHQ\HOORZ
Fig. 6 Connection for assembly cable
► Switch on mains.
► You can now set the end positions with the elero
assembly cable.
5.4.2 Radio connection (transmitter operation)
Blau (Neutralleiter)
Schwarz
Braun
Grün-gelb
Fig. 7 Radio connection (transmitter operation)
► Connect cable wires „UP“ and „DOWN/CLOSE“ together
to phase L (outer conductor).
► Switch on mains. The drive buzzes and travels upwards
and downwards for a short time.
The drive is in radio mode.
Teaching or deleting the transmitter, fixing or deleting the
blind positions: see instructions for the corresponding hand-
held transmitter.
5.4.3 Operation in non-radio mode
Important
If the drive is to be operated in non-radio mode, follow the
instructions for the RolMotion M (article no. 138251001).
5.5 Setting the end positions
Important
To use travel profiles, the upper and lower end positions
must first be set. First program the upper end position,
then the lower end position.
As long as the direction of travel does not have the
correct logical assignment, the upper end position actually
corresponds to the lower end position.
The end positions are set alternatively
• using the
elero assembly cable (correct connection
according to Chapter 5.5.1) or
• using a programmed transmitter. (To
program a transmitter, see Chapter 5.7.)
HOHUR HOHUR
%OXHQHXWUDOFRQGXFWRU
%ODFN
%URZQ
*UHHQ\HOORZ
© elero GmbH EN | 5
Assembly | Electrical connection | relief function