Elektro-Automatik EA-PS 10000 4U, Manual

Page: 2 / 76

© EA Elektro-Automatik in 2022, this information is subject to change without notice 2 06230900_manual_ps_10000_4u_30kw_en_01
TABLE OF CONTENTS
1. General
1.1 About this document 4
1.1.1 Retention and use 4
1.1.2 Copyright 4
1.1.3 Validity 4
1.1.4 Symbols and warnings 4
1.2 Warranty 4
1.3 Limitation of liability 4
1.4 Disposal of equipment 5
1.5 Product key 5
1.6 Intended usage 6
1.6.1 Symbols and warnings on the device 6
1.7 Safety 7
1.7.1 Safety notices 7
1.7.2 Responsibility of the operator 8
1.7.3 Requirements to the user 8
1.7.4 Responsibility of the user 8
1.7.5 Alarm signals 9
1.7.6 Functionality test 9
1.8 Technical data 10
1.8.1 Approved operating conditions 10
1.8.2 General technical data 10
1.8.3 Specific technical data 11
1.8.4 Views 15
1.8.5 Control elements 20
1.9 Construction and function 21
1.9.1 General description 21
1.9.2 Block diagram 21
1.9.3 Scope of delivery 22
1.9.4 Accessories 22
1.9.5 Options 22
1.9.6 The control panel (HMI) 23
1.9.7 USB port (rear side) 25
1.9.8 Interface module slot 26
1.9.9 Analog interface 26
1.9.10 “Share BUS” connector 26
1.9.11 “Sense” connector (remote sensing) 27
1.9.12 Master-Slave bus 27
1.9.13 Ethernet port 27
1.9.14 Water cooling 28
2. Installation & commissioning
2.1 Transport and storage 29
2.1.1 Transport 29
2.1.2 Packaging 29
2.1.3 Storage 29
2.2 Unpacking and visual check 29
2.3 Installation 29
2.3.1 Safety procedures before installation and use 29
2.3.2 Preparation 29
2.3.3 Installing the device 30
2.3.4 Installing the water cooling 31
2.3.5 Connection to AC supply 33
2.3.6 Connection to DC loads 36
2.3.7 Connection of remote sense 38
2.3.8 Grounding of the DC output 39
2.3.9 Installation of an interface module 39
2.3.10 Connecting the analog interface 40
2.3.11 Connecting the Share bus 40
2.3.12 Connecting the USB port (rear side) 40
2.3.13 Initial commission 40
2.3.14 Commission after a firmware update or a long
period of non-use 40
3. Operation and application
3.1 Personal safety 41
3.2 Operating modes 41
3.2.1 Voltage regulation / Constant voltage 41
3.2.2 Current regulation / constant current / current
limiting 42
3.2.3 Power regulation / constant power / power
limiting 42
3.2.4 Internal resistance regulation 42
3.3 Alarm conditions 43
3.3.1 Power Fail 43
3.3.2 Overtemperature 43
3.3.3 Overvoltage protection 43
3.3.4 Overcurrent protection 43
3.3.5 Overpower protection 43
3.3.6 Safety OVP 44
3.3.7 Share bus fail 44
3.4 Manual operation 45
3.4.1 Switching on the device 45
3.4.2 Switching the device off 45
3.4.3 Configuration via the menu 45
3.4.4 Adjustment limits 53
3.4.5 Changing the operating mode 53
3.4.6 Manual adjustment of set values 54
3.4.7 Switching the DC output on or off 55
3.4.8 Recording to USB stick (logging) 55
3.4.9 The quick menu 56
3.4.10 The graph 57
3.5 Remote control 58
3.5.1 General 58
3.5.2 Control locations 58
3.5.3 Remote control via a digital interface 58
3.5.4 Remote control via the analog interface 60