elektraLite LXE 700 Wash User Manual Download Page 5

 -                                     LXE700 wash 

Installation via the Omega U Brackets. 

1

2

3

4

(1)Omega-holders

(2)C lamp

(3)Safety -rope

(4)Quic k -loc k  fas tener

 

 
 
 

Screw one clamp (the clamp is not provided with 

LXE 700 Wash

) onto each of the two Omega U brackets 

supplied with 

LXE 700 Wash. 

 

Insert the quick-lock fasteners of the first Omega bracket into the respective holes on the bottom of 

LXE 700 

Wash

. Tighten the quick-lock fasteners fully clockwise. Install the second Omega U bracket. Please do not use 

pliers, crest wrenches and the like to turn the quick-lock fastener. If you do, there is very real likelihood that you 
will break the Omega bracket. (These can be replaced at a substantial cost to your boss!)   
Pull the safety cable through the holes on the bottom of the base and over the trussing or any secondary fixing 
point. Do not clamp the cable to the U bracket or clamp. That is not a secondary safety point. 
A secondary safety point is any point that will adequately hold 

LXE 700 Wash 

if the U brackets, clamps or the 

fixtures base breaks or fails. Then the safety cable would be the backup and stop the fixture from falling to the 
ground. 

Summary of Contents for LXE 700 Wash




















Reviews: