Printing and typographical errors reserved.
ELECTRONIC ASSEMBLY reserves the right to change specifications without prior notice.
Page 16
EA eDIPTFT32-A
EA eDIPTFT32-A: Macro commands
after
reset
Command
Codes
Remarks
Macro commands
Run macro
ESC
M
N
no
Call the (normal) macro with the number no (max. 7 levels)
Run touch macros
T
no
Call the touch macro with the number no (max. 7 levels)
Run port macro
P
no
Call the port macro with the number no (max. 7 levels)
Run bit macro
B
no
Call the bit macro with the number no (max. 7 levels)
Run matrix macro
X
no
Call the matrix macro with the number (max. 7 levels)
Run process macro
C
no
Call the process macro with the number (max. 7 levels)
Run analogue macro
V
no
Call the analogue macro with the number no (max. 7 levels)
Disable macros
ESC
M
L
type
n1
n2
Macros of the type'N','T','P','B','X','C' or 'V' (type 'A' = all macro types) are disabled from the
number n1 to n2; i.e. no longer run when called.
Enable macros
U
type
n1
n2
Macros of the type 'N','T','P','B','X','C' or 'V' (type 'A' = all macro types) are enabled from number
n1 to n2; i.e. run again when called.
Select macro/image page
ESC
M
K
n1
A page is selected for macros and images n1=0 to 15. if a macro/image is not defined in the
current page 1 to 15, this macro/image is taken from page 0 (e.g. to switch languages or for
horizontal/vertical installation).
Save macro/image page
W
the current macro/image page is saved (when used in process macros)
Restore macro/imagepage
R
the last saved macro/image page is restored
Automatic (normal-) macro
Macro with delay
ESC
M
G
n1
n2
Call the (normal) macro with the number n1 in n2/10s. Execution is stopped by commands (e.g.
receipt or touch macros).
Autom. macros once only
E
n1
n2
n3
Automatically run macros n1 to n2 once only; n3=pause in 1/10s. Execution is stopped by
commands (e.g. receipt or touch macros).
Autom. macros cyclical
A
n1
n2
n3
Automatically run macros n1 to n2 cyclically; n3=pause in 1/10s. Execution is stopped by
commands (e.g. receipt or touch macros).
Autom. macros ping pong
J
n1
n2
n3
Automatically run macros n1 to n2 to n1 (ping pong); n3=pause in 1/10s. Execution is stopped,
for example, by receipt or touch macros.
Macro processes
Define macro process
ESC
M
D
no type
n3
n4
zs
A macro process with the number no (1 to 4) is defined (1=highest priority).
The process macros n3 to n4 are run successively every zs/10s.
type: 1=once only; 2=cyclical; 3=ping pong n3 to n4 to n3
Macro process interval
Z
no
zs
a new time zs in 1/10s is assigned to the macro process with the number no (1 to 4).
if the time zs=0, execution is stopped.
Stop macro processes
S
n1
All macro processes and animations are stopped with n1=0 and restarted with n1=1 in order,
for example, to execute settings and outputs via the interface undisturbed
1
EA eDIPTFT32-A: Analogue input AIN1, AIN2 commands
after
reset
Command
Codes
Remarks
Commands for analogue inputs
Calibration
ESC
V
@
ch
xx1
Calibration procedure is as follows:
1.) Apply defined voltage (3..5V) to AIN1 (channel1) or AIN2 (channel2)
2.) Run this command with channel information ch=1..2 and xx1=voltage value [mV] (16-Bit)
e.g. 4.0V on AIN1; Command: '#V@1,4000;'
not
calib
rated
Enable/disable AIN scan
ESC
V
A
n1
n1=0 disables input scan for AIN1 and AIN2; n1=1 enable input scan
0
Send analog value
D
ch
Voltage in [mV] will be sent (to sendbuffer) for channel ch=1..2
Limit for analog macro
K
ch
n1
n2
n3
Sets two limits for channel ch=1..2.
n1=lower limit [mV/20]; n2=upper limit [mV/20]; n3=hysteresis [mV]
Related to this limits serveral analogmacros can be started automatically.
0
Redefine analoguemacro
(since V1.1)
ESC
V
M
n1
n2
Assign analoguemacrofunction n1=0..19 with analoguemacro number n2=0..255.
Bargraph for AIN1/AIN2
ESC
V
B
ch
no
Assigns bargraph no=1..20 to analogue input ch=1..2
(it is possible to assign more than one bargraph to an anlogue input).
Define start- endvalues (sv, ev) for bargraph in [mV/20] (see comand 'ESC B RLOU')
Instrument for AIN1/AIN2
+
ch
no
Assigns instrument no=1..4 to analogue input ch=1..2
Define start- endvalues (sv, ev) for bargraph in [mV/20]
Redraw bargraph
R
ch
Redraw all bar graphs defined for channel ch=1..2
User values - Format text output
User value color
ESC
F
V
ch
fg
bg
Set color for string output of channel ch=1..2; fg= foreground, bg= background color
8,1
User value Font
V
F
ch
n1
Set font n1 for channel ch=1..2
5
User value zoom
Z
ch
n1
n2
Set zoom factor for channel ch=1..2; n1=X-Zoom 1x..8x; n2=Y-Zoom 1x..8x
1,1
User value additional
width/height
Y
ch
n1
n2
n1=0..15: additional width left/right;
n2=0..15: additional height top/bottom for channel ch=1..2;
0, 0
User value angle
W
ch
n1
Set writing angle for channel ch=1..2; n1=0: 0°; n1=1: 90°; n1=2: 180°; n1=3: 270°;
0
User values / scaling
ESC
V
E
ch
format string
...
NUL
Set user value for channel ch=1..2.
Format String: "mV1=uservalue1;mV2=uservalue2". 'NUL' ($00) = termination
Assign two voltages (0..5000mV) to user defined values
max. range: 4 1/2 digits 19999 + decimal point ('.' oder ',') + sign
e.g. display for 2000 mV input should be "-123.45" and "0.00" for 1000mV
Format String: "2000=-123.45;1000=0"
0
=0.00
5000
=5.00
Send user value
ESC
V
S
ch
This will send current voltage as formated string for channel ch=1..2 to sendbuffer
Display on terminal
T
ch
Show formated string of channel ch=1..2 on termial window
Display user value
G
ch
xx1
yy1
Show formated string of channel ch=1..2 at coordinate xx1,yy1
