4 - ENGLISH
Kickback
Machines equipped with blades may produce a violent
kickback on contact with solid bodies. The blade is
capable of amputating arms and legs. The force of the
kickback can cause the operator to lose control of the
machine.
Kickback can also occur when cutting with any type of
blade in the hazardous zone (see
N1
); we therefore
recommend cutting using the remaining zone.
This section describes the safety devices on the
machine, and provides instructions for control and
maintenance to keep them in perfect working order. The
section “
General Description
” will help you to identify the
parts described in this section. The risk of accidents
increases considerably if maintenance is not performed
regularly or is not done professionally. In case of any
doubts contact an authorized service center.
Safety lever
• This device serves to prevent accidentally pressing the
throttle trigger (fig.
A
no.
3
). In fact, the trigger (fig.
A
no.
3
), can only be pressed if the safety lever is pressed at
the same time (fig.
A
no.
19
).
• By means of 2 separate springs, upon releasing the
grip, the throttle trigger (fig.
A
no.
3
) and safety lever
(fig.
A
no.
19
) return automatically to their original
positions.
Engine stop device
• Turn the stop button Stop (fig.
A
no.
7
) to O / STOP to
stop the engine.
• To make sure this button works properly, start the
engine and check that it stops when the Stop button
(fig.
A
no.
7
) is turned to the Stop position.
Protection for transport
The guard covers the sharp extremities of the blade when
the machine is in the resting position for transport or
storage (fig.
A
no.
23
).
Safety guard
• This very important safety device (fig.
A
no.
18
)
prevents any objects that come into contact with the
cutting device, or the grass itself, from flying up and
striking the operator. It should be checked regularly;
check the assembly and make sure the fastening
screws are tight (see “
Assembly of safety guard
”).
• If you strike any hard objects that cause structural
damage to the guard on the cutting device, take the
machine to an authorized service center for
replacement of the guard.
Safety pole guard
This device, fastened to the machine, ensures a
minimum distance between the operator and the cutting
device during use, and prevents the machine from
striking and injuring the operator if the blade hits a hard
surface (fig.
A
no.
20
).
Muffler
• The muffler serves to reduce the noise level to a
minimum and to route the exhaust fumes produced by
the combustion engine away from the operator.
• Follow these procedures for safe use of the brush
cutter.
CAUTION!
Always use a sharp blade. A blade
with worn teeth can create problems in cutting
and cause the blade to kickback.
CAUTION!
Do not sharpen a damaged or worn
blade. Replace it with a new one.
CAUTION!
We recommend the use of original
accessories and replacements, which can be
purchased from authorized distributors. The use
of other accessories and replacements increases
the danger of accidents and in this case the
manufacturer has no liability for damages to
persons and/or property.
C. Description of the safety devices on the machine,
controls to be made and maintenance of the safety devices
CAUTION!
Do not use the machine for any
reason with its safety devices out of order.
CAUTION!
Never use the machine with its Safety
lever pressed with adhesive tape, string or other.
CAUTION!
Before applying the guard switch off
the engine and wait for the cutting device to stop.
Use the blade guard whenever you have to
transport and store the machine.
CAUTION!
Never use the machine for any reason
without the specific safety devices listed below!
Though they do not entirely eliminate all risks,
they greatly reduce the danger.
CAUTION!
Never use the machine for any reason
without the recommended safety guard for the
cutting device in use. The use of an inadequate or
defective guard can cause serious injuries.
Periodically, check its conditions and replace if
necessary.
CAUTION!
Never use a brush cutter without its
safety pole guard correctly in place.
CAUTION!
The muffler can get very hot during
use and should be allowed to cool for some time
after switching off the engine. Therefore, take
special precautions when, for any reason, you
have to touch the area around the muffler.
CAUTION!
Fire hazard. Never use the machine
with a defective or damaged muffler.
