manualshive.com logo in svg

Electrolux P6000 (Nexus) Series, Service Manual

Share
Download
Electrolux P6000 (Nexus) Series Service Manual Download Page 73

SOI/DT 2002-05 eb

 73 

599 35 23-17  

8.9 Water 

distributor 

8.9.1 General 

characteristics 

The water distributor is used in models with MWM electronic control systems, and performs the following 
functions: 

ƒ

  It actions the levers in the detergent dispenser in order to duct water through the various compartments 

during the course of the washing cycle. 

ƒ

  Drawing power from the main PCB, it powers the following components:  

Ö

 

Cold water solenoid valve 

Ö

 

Circulation pump 

Ö

 

Drain pump 

 
 
 
 

 
1. PCB 
2. Water 

distributor 

3.  Detergent dispenser lever system 

 
 
 
The water distributor is actioned and controlled by the electronic control system. The motor of the distributor 
is powered via a triac on the main PCB. 
Before the motor is switched on, all the loads are disconnected from the power supply in order to reduce 
wear of the contacts. 
The motor is powered only for the time necessary to move the levers from one position to the next. 
During the washing programme, the distributor may perform several complete rotations in order to move to 
the positions necessary for the completion of the cycle. 
 

8.9.2 Operating 

principle 

 
 
 
 
 

1. Motor 

 

2. Gearwheel

 

3. Camme

 

4. Lever actioning arm

 

5. Brush contacts

 

6. Contact base

 

7. Casing

 

8. Cover

 

 
 
 
 
 
 
The motor (1), when powered, moves the camme (3) by means of the gears (2). The camme moves the arm 
that moves the lever actioning arm (4). 
The camme is fitted with brush contacts (5) which slide in contact with the copper tracks on the contact base 
(6). The contacts close in different ways (see diagram) depending on the position of the camme. 
The camme requires 15 seconds to perform one complete rotation. As the contact base is divided into 36 
sections, passage from one position to the next requires about 0.4 seconds. 
 
 

Summary of Contents for P6000 (Nexus) Series























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands