manualshive.com logo in svg

Electrolux P6000 (Nexus) Series, Service Manual

Share
Download
Electrolux P6000 (Nexus) Series Service Manual Download Page 103

SOI/DT 2002-05 eb

 103 

599 35 23-17  

9.5.3 Thermostat/NTC 

sensor 

a.  Remove the rear cabinet shell.  
b.  Detach the drive belt from the pulleys (if necessary). 
c.  Detach the wiring connectors (fixed-temperature thermostats and NTC 

sensors) 

d.  Remove the thermostat/sensor from the sealing ring (41). Refer to 

section 9.2.7 for removal of the adjustable thermostat (42). 

 

Re-assembling the NTC sensors (version with "long" bulb): 

The sensor must be replaced with the groove in the connector base facing 
downwards (43). 

 
 
 
 
 
 
 
 
 
 
 
 

9.5.4 Heating 

element 

a.  Remove the rear cabinet shell. 
b.  Detach the drive belt from the pulleys. 
c.  Detach the wiring connectors (42). 
d.  Remove the screw which secures the heating element flange. 
e.  Push the nut on the heating element flange towards the interior of the tub (44). 
f.  Remove the heating element (45). 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for P6000 (Nexus) Series























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands