manualshive.com logo in svg

Electrolux P6000 (Nexus) Series, Service Manual

Share
Download
Electrolux P6000 (Nexus) Series Service Manual Download Page 30

SOI/DT 2002-05 eb

 30 

599 35 23-17  

6.1.1  Washing machine with 32 cm-depth cabinet 

 
 

1.  Front cabinet shell 
2. Tub 
3.  Drum rotation motor 
4. Drain 

pump 

5. Damper 
6. Heating 

element 

7. Thermostat 
8. Pressure 

switch 

9. Capacitor/suppressor 
10. Base 
 

 
 
 
 
 
 
 
 

6.2 Base 

1. Base 
2. Filter 

body 

3. Drain 

pump 

4. Dampers 

 
The base is built in "CARBORAN", a specially-
developed plastic. 
As well as the two cabinet shells, the filter body, drain 
pump, dampers and (if featured) the circulation pump 
and motor control system are all housed in the base. 
 
 
 
 
 

6.3  Control panel support 

 

1. Timer 
2. Adjustable 

thermostat 

3. Push-button 
4. Detergent 

dispenser 

 
 
 
 
 
 
 
The control panel support (in galvanized sheet metal) is secured by a series of screws to the two cabinet 
shells. 
Several components are fitted to the support: timer, adjustable thermostat, pushbuttons, capacitor, pressure 
switches, detergent dispenser and control panel. 
Also secured to the support are the two suspension springs for the washing group. 
 
 

Summary of Contents for P6000 (Nexus) Series























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands