manualshive.com logo in svg

Electrolux P6000 (Nexus) Series, Service Manual

Share
Download
Electrolux P6000 (Nexus) Series Service Manual Download Page 104

SOI/DT 2002-05 eb

 104 

599 35 23-17  

9.5.5 Detergent 

dispenser 

 
 
 
 
 
 
 
 
 
 
 
 
a.  Remove the rear cabinet shell. 
b.  Unscrew the clamp and detach the tube from the 

detergent dispenser to the tub 

c.  Detach the steam venting tube from the tub (if present) 
d.  Extract the detergent drawer (8) 
e.  Remove the screw which secures the control panel to 

the detergent dispenser (9) 

f.  Remove the screws which secure the detergent 

dispenser to the cross-member 

g.  Remove the solenoid valve(s) (if fitted to the dispenser) 

or detach the tube(s) from the dispenser to the solenoid 
valve 

h.  Detach the lever mechanism (46), if present 
i.  Release the two lateral anchor tabs from the front cross-

member (47a) and, at the same time, push the detergent 
dispenser towards the rear 

j.  Press down the lower anchor tab which secures the 

dispenser to the front cross-member (47-b) 

k.  Lower the washing group and pull the dispenser out 

 

9.5.6  Removing the duct from the dispenser 

 
a.  Remove the dispenser 
b.  Remove the lever regulation pin (if present) by pressing 

the two anchor tabs (48) 

c.  Release the clamp and the anchor tabs for the duct from 

the lower part of the dispenser (49) 

 

From inside the dispenser, the engineer can access: 

a.  The water intake nozzle, which is removed by lifting from the dispenser 
b.  The steam venting tube 
c. The 

water 

distributor 

 

9.5.7 Water 

distributor 

This operation may be performed without 
removing the dispenser: 

 
a.  Remove the detergent drawer (8) 
b.  Release the spring (50a) 
c.  Release the anchor tab and slide out (50b) 
d.  Rotate and extract the distributor from 

inside the dispenser 

 
 

Note

: When re-assembling, the specific grease 

MUST be applied to the distributor (50c) 

 

48 

49 

a 

b

c 

50 

 8 

9 

Summary of Contents for P6000 (Nexus) Series























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands