background image

6

TEMPERATURE CONTROL

The thermostat ensures that the required

temperature is maintained in the freezer.

Adjust the temperature by turning the

control knob with a coin that fits the

groove. Turning the thermostat control

knob towards no. „MAX” makes the

temperature in the freezer colder, and

turning the control knob towards no. 1

makes the temperature warmer.
The correct setting can be found by

measuring the  temperature of the top

package in the middle of the freezer. This

should not have a temperature warmer

than -18°C.

OPENING/CLOSING THE LID

The lid is fitted with a tightly closing sealing

strip to prevent moisture getting inside the

freezer and increasing the amount of frost

formed. When the lid is opened the air

inside the freezer becomes slightly warmer

and expands. As soon as the lid is closed

again the air is cooled immediately. This

may lead to the creation of a vacuum which

makes it hard to open the lid immediately

after it has been closed. This is quite

normal. Wait a few minutes until the

vacuum has disappeared, then open the

lid by pulling gently. Never pull the handle

violently.

CONTROL PANEL

The red signal light remains illuminated to

indicate that the internal temperature of

the applkiance is correct for safe of frozen

food. If the temperature is to high in the

appliance the light will go out.
The  light may go out the following

reasons :

There is a power failure.
The lid has been recently opened.
A large quantity of food has been

added to the appliance.
There is a fault.

FREEZING

It is important that fresh food placed in the

freezer is frozen quickly, and that the food

already in the freezer is heated as little as

possible in this connection. If more than

3-4 kg of food is to be frozen:

Turn the control knob to „MAX”. The

freezer will now run continuously,

creating a sufficient reserve of the

temperature required.
Turn the control knob to „MAX” 6-24

hours before placing fresh food in the

freezer, depending on how much food

is to be frozen.
Place the food in the freezer and leave

the control knob set to „MAX” for about

24 hours more.

Thermostat

control knob

Signal

light

Summary of Contents for KCF264A













Reviews: