manualshive.com logo in svg

Electrolux FDB1050RE 2005, Service Manual

Share
Download
Electrolux FDB1050RE 2005 Service Manual Download Page 15

14

HEATING ELEMENT

1. Disconnect the dishwasher from electrical supply
2. To remove element disconnect wiring and remove

two element mounting nuts.

3.  Lift terminal ends from tub.

4. Raise locking hook on mounting brackets to

slide element from brackets.

FLOAT SWITCH AND MOUNT BRACKET

1. Disconnect the dishwasher from electrical supply
2. For ease of service remove outer door panel and

kick plate, remove wires to float switch.

3. Unscrew Phillips screw holding assembly to

tub, there is a
hole provided in
the actuator
lever to access
screw.  Screw
will remain in
assembly once
removed.

WATER VALVE

1. Disconnect the dishwasher from electrical supply
2. Turn water off to dishwasher before replacing

valve

3. Gain access to valve remove wiring, water line,

and fitting from valve.

4.  Water valve is secured with two screws.

DRAIN PUMP

Precision Wash

1. Disconnect the dishwasher from electrical supply
2. Gain access to drain pump remove wiring and

hoses from pump. Dishwasher may need to be
pulled forward to access drain pump.

3. Pump is mounted with two screws through

mounting bracket.

Drain hose

Connector hose

Mounting

screws

Wire terminals

Water  line connection

Precision Direct Wash System.

1. Disconnect the dishwasher from electrical supply
2. Gain access to drain pump remove wiring and

drain hose from pump.  Slide clamp on hose
between pump and sump to the center of hose

NOTE:

  When removing the drain pump, the hose

clamp on the connector hose from the drain pump
to the sump, it is recommended to slide the clamp
back on the sump end of the hose.  This will
make it easier to reinstall the new drain pump.

Summary of Contents for FDB1050RE 2005





































Reviews:

No comments

Brands by name

Popular brands

Load more brands