manualshive.com logo in svg

Electrolux FDB1050RE 2005, Service Manual

Share
Download
Electrolux FDB1050RE 2005 Service Manual Download Page 14

13

CENTER SPRAY ARM (PRECISION
DIRECT MODELS)

1. Pull upper rack forward to gain access to spray

arm.

2. Center spray arm and delivery tube are an

assembly, push this assembly to the rear to
loosen and remove from rack.

DOOR LATCH

1. Disconnect the dishwasher from electrical

supply

2. Remove outer door panel
3. Remove console
4. Remove wires from both door switches
5. Remove two Torx screw holding latch

6.  Make sure both white wires are on one switch

and both black wires are on the opposite
switch.

DETERGENT/ RINSE AID DISPENSER

1. Disconnect the dishwasher from electrical supply
2. Remove outer door panel
3. Disconnect wiring from dispenser

4. Remove six Phillips screws and carefully push

dispenser into the tub

DOOR SEAL

UPPER RACK

1. To remove rack, unsnap and remove retainers

at end of metal track.  Once retainers are
removed, pull rack straight out.

2. Each track roller is secured with a T-25 TORX bolt.

When reinstalling the roller care must be taken not
to cross thread the screw opening in tub.

1. Door seal just pulls out of channel around tub.
2. To replace find center of gasket make sure back

goes into channel first. Back is marked with a color
stripe.

3. Starting at center top

press gasket into
channel just to hold in
place

4. Go to bottom on either side

find block molded into
bottom of tub fill block with
gasket.

5. Form gasket into an “L” press gasket up channel

in several spots.

6. Repeat steps 4 and

5 for opposite side

7. Close door to seat

seal.

Door

Switchs

Mounting Screws

Hook opened to
remove retainer

Retainer on rear of center

arm delivery tube

Summary of Contents for FDB1050RE 2005





































Reviews:

No comments

Brands by name

Popular brands

Load more brands