Electrolux EWT806 User Manual Download Page 7

Preparing for your wash

electrolux water aid washing machine  

preparing for your wash 

 

7

Detergent use

•   Don’t use the wrong type of detergent. You must use a 

low sudsing detergent designed for front load washing  
machines or high efficiency top loaders, such as Cold 
Power for Front Loaders and High Efficiency Top 
Loaders or detergents labelled “Matic”.

•   Don’t use soap-based products in your washing machine.
•    Don’t use too much detergent. This will give you too 

many suds causing low spin speeds, poor rinsing and  
overloading the motor during spin stages of the wash 
program.

•   Don’t use too little detergent because you will get a poor 

wash. If you think you need more, increase dosages by  
only small amounts to avoid excessive suds.

Add the detergent

When using the washing machine for the first time, check 
that the dispenser is set for the type of detergent you will 
use. To do this, proceed as follows:
1.  Pull the dispenser drawer forward until it stops.
2.   Lift the front of the drawer up and forward to remove it 

from the runners.

3.   Check the position of the flap at the rear of the 

detergent compartment in the dispenser drawer.  
(Factory setting is flap up for powder.)

4.   Clip the flap down if you are going to use liquid detergent.

5.   Refit the dispenser back into its runners. 

 Remember: If you change the type of detergent 
you use, the position of the flap will need 
changing. See above. 

6.   You are now ready to add detergent. Measure the 

recommended amount on the detergent package into a 
cup and then pour it into the detergent compartment of 
the dispenser drawer.

caution

Use only low sudsing detergent designed for use in 
front load or high efficiency top load washing machines.

When using liquid detergent, some may leak out of the 
dispenser into the wash load earlier than expected through 
small openings in the back of the dispenser. These 
openings are to help the ushing out of detergent.

step 8 cont. over

clip flap up for 
powder

clip flap down for 
liquid

add detergent

Sort your washing into separate wash loads

Each load of washing should contain clothing which needs 
the same washing conditions. For example, you should not 
wash delicate clothes with very dirty work clothes. Colour 
fast and non-colourfast fabrics should be separated.
Knowing the type of fabrics you have and how dirty they 
are will help when you make selections from the wash 
program options. Some fabrics are lint collectors and can 
pick up lint, dirt and colour from other fabrics which are lint 
producers. Some examples are listed below:

Lint collectors

Lint producers

Corduroy

Towels

Synthetics

Nappies

Permanent press fabrics

Chenille/Candlewick

tips and information

Make sure that you wash lint collectors separately from lint 
producers.

Check your clothes to avoid damage
•   Empty all pockets. Close all hooks and zippers to avoid 

snagging clothes.

•   Wash bras, pantyhose and other delicates in a mesh 

laundry bag, which you can purchase from your  
supermarket.

caution

Pre-treatment sprays and stain removers

• 

 

 Pre-treatment  sprays and stain removers can damage 
plastic components on your washing machine.

• 

 

 If you use pre-treatment  sprays or stain removers,  
apply them to the clothing well away from your 
washing machine.

Load the washing machine

When loading the clothes into your washing machine, there 
are four things to remember:
•   Clothes must be loaded evenly around the agitator. For 

best results load small items first, followed by large items.

•   Clothes must not be wrapped around the agitator.
•   The washing machine must not be overloaded. Clothes 

must be able to move around during washing.

•   The load should contain only three or four large items, 

for example, sheets. The rest of the load should be 
small items. A mixed load of large and small items will 
wash cleaner than a load of all large items.

Summary of Contents for EWT806


































Reviews: