How to save energy
Avoid pulling the appliance in a sunny place and
near anything that gives off heat.
Be sure that the condenser and the compressor
are well ventilated. Do not cover the sections
where ventilation is.
Wrap products in tightly closing dishes or cling
film to avoid building up unnecessary frost.
Do not leave the door open longer than
necessary and avoid unnecessary openings.
Put warm foods into the appliance when they are
at room temperature.
Keep the condenser clean.
The appliance and environment
This appliance does not contain gasses which
could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The
appliance shall not be discarded together with the
urban refuse and rubbish. Avoid damaging the
cooling unit, especially at the rear near the heat
exchanger. Information on your local disposal
sites may be obtained from your municipal
authorities.
The materials used on this appliance marked with
the
symbol are recyclable.
Maintenance
Defrosting
Bleeding part of the moisture of cooling chambers
in form of frost and ice goes with the operation of
the appliance.
Thick frost and ice has an insulating effect, so it
reduces cooling efficiency as the temperature
increases in the cooling chambers and they need
more energy.
At this type of appliance defrosting the cooling
plate of the refrigerator is automatic without any
external intervention. The thermostatic control
interrupts the operation of compressor at regular
intervals for more or less time during this cooling
is interrupted the temperature of the cooling plate
goes above 0 °C due to interior heating load of the
compartment, so defrosting occurs. When the
surface temperature of the cooling plate has
reached +3 - +4 °C the thermostatic control
restarts operation of the system.
Melting water flows through defrost water outlet
leaded through the back into the evaporative tray
maintained on the top of compressor and
evaporates due to its warmth.
Check and clean the outlet of melting water
coming during defrosting regularly
-
a label inside the appliance warns you for
this. If it is clogged the melting water
gathered can cause earlier failure as it can
go to the insulating of the appliance.
Clean the melting water outlet with the supplied
pipe scraper that can be seen in the figure above.
The pipe scraper has to be stored in the outlet.
The most typical case of clogging up in the
melting water outlet when you put food wrapped
in some paper into the appliance and this paper
contacts back plate of the refrigerator and freezes
to it. If you remove the food right at this moment
the paper will tear and it can cause clogging up in
the outlet by gelling into it.
So you are asked to be careful because of the
above when placing foods wrapped in paper into
the appliance. In case of increased demand e.g.
during heat waves, the refrigerator temporarily
happens to operate constantly. During this the
automatic defrosting is ineffective.
i
i
6
Instructions for the Installer
Technical data
Installing the appliance
Transportation, unpacking
It is recommended to deliver the appliance in
original packaging, in vertical position
considering the protective warning on packaging.
After each transportation the appliance must not
be switched on for approx. 2 hours.
Unpack the appliance and check if there are
damages on it. Report possible damages
immediately to the place you bought it. In that
case retain packaging.
Cleaning
Remove every adhesive tape and everything else,
which ensure the accessories not to move in the
appliance.
Wash the inside of the appliance using lukewarm
water and mild detergent. Use soft cloth. After
cleaning, wipe out the inside of the appliance.
Placement
The ambient temperature has an effect on the
energy consumption and proper operation of the
appliance. When placing, take into consideration
that it is practical to operate the appliance
between ambient temperature limits according
to the climate class that is given i
the chart below and can be found in the data label.
If the ambient temperature goes below the lower
data the temperature of the cooling compartment
can go beyond the prescribed temperature.
If the ambient temperature goes beyond the upper
data this means longer operating time of the
compressor, breakdown in the automatic
defrosting increasing temperature in the cooling
compartment or increasing energy consumption.
When placing the appliance ensure that it stands
level. This can be achieved by two adjustable feet
(1) at the bottom in front.
9
