Electrolux ei28bs55is1 Page 10 Use And Care Manual Download

Page: 10 / 49

To remove the refrigerator doors:

1 Trace lightly around the door’s top hinges

with a pencil. This makes reinstallation easier.

2 Disconnect the harness by grasping both

sides of the connector firmly, depress the

latch, and pull apart. Remove the two

screws from the top hinge. Lift the door

off of the bottom hinge and set it aside.

3 Detach the water tube from the

connector located behind the refrigerator

and pull the tube back out to the front

of the unit. The connector releases

when you press inward on the outer

sleeve while pushing the tube toward the

connector then while continuing to hold

in the sleeve, pull the tube away.

4 Unscrew the three lower hinge screws

and hinge if necessary.

Removing the Doors

Getting through narrow

spaces

If your refrigerator will not fit through an

entrance area, you can remove the doors.

Check first by measuring the entrance.

To prepare for removing the doors:

1 Make sure the electrical power cord is

unplugged from the wall outlet.

2 Open the freezer drawer and remove the

toe grille (see “Installation” section).

3 Remove any food from the door shelves

and close the doors.

To remove the top hinge covers:

1 Remove the two screws from each cover

over the top door hinges.

2 Lift inside edge of hinge cover and tilt back.

NOTE

DO NOT remove the ground screw from

hinge.

Rear

Cover

Screw

Ground

Screw

Top

Hinge

Top Hinge

Cover

Hinge

Screws

Multi-wire

Cables

Leave

Hinge

With

Door

Front

Cover Screw

Water

Line

Rear

Cover

Screw

Front

Cover Screw

Top Hinge

Cover

Hinge

Screws

Two Wire

Cables

Leave

Hinge

With

Door

Top

Hinge

Ground

Screw

NOTE

Use care while pulling the water tube from

the unit to be sure you do not kink it.

Summary of Contents for ei28bs55is1


















































Search results

Summary of Contents for ei28bs55is1

Reviews:

Related manuals for ei28bs55is1

Brands by name

Popular brands

Electrolux ei28bs55is1, Use And Care Manual

Search results

Summary of Contents for ei28bs55is1

Reviews:

Related manuals for ei28bs55is1

Brands by name

Popular brands