• Electrical characteristics:
A
: Machine
C
: Supply voltage
D
:
Frequency
E
: Nominal power
F
: Rating of the fuse of the mains cable (Amperes) see XBM20.
• Check the direction of rotation
- Of the planetary gear, anti-clockwise (see arrow on head)
or the tool, clockwise : factory setting.
In the event of a problem, see §5.2 to reverse the direction of
rotation.
2.
3a
Use and Safety
Note:
- To change the time being counted down, press on button
C then change using buttons A and B;
- resume cycle by pressing button D.
- The time displayed at the beginning of the cycle remains in
memory
- To permanently interrupt a cycle underway, press button C
twice.
b) Continuous operation
- Select ---- on E by pressing and holding button A
- Start by pressing button D
- Stop by pressing button C
c) Speed variation and pre-selected speeds
Speeds I, II and III (D keys) are programmed in the factory. The
speed can be varied at any time by pressing on keys F and G.
Similarly, the speed can be returned to one of the programmed
settings by pressing on a D key.
• Programming the D keys
- Switch on the power to the appliance
- Start the appliance by pressing button I, II or III depending on
the speed to be programmed
- Adjust the speed using the + and – buttons
- Press and hold the key on the timer until the speed
display goes out.
- Repeat the operation for each speed (I, II, III)
- The programming is deleted when the power to the appliance
is turned off.
3.
1
2.
3b
3.
1
OPERATION - SAFETY
• The safety of the user is guaranteed by:
- The motor halting when the safety guard is opened.
- The design of the guard that allows products to be added
perfectly safely during operation.
- The motor halting when the cradle is lowered. It will not start
again when the ON switch is pressed.
- The need to press the ON button after the machine has been
stopped («no volt release» device)
- Protection against current and power surges, drops in power
and the motor overheating.
- Compliance with the instructions given in this manual for using,
cleaning and maintaining the machine.
•
Control panel
A Reduce time setting on timer
B Increase time setting on timer
C STOP button
D START button avec vitesse présélectionnée.
E Timer display
F Increase speed
G Reduce speed
H Speed display
• The beater will start normally when the bowl-holder cradle
assembly is in the working position,
- The safety guard is fi tted and down,
- The timer is set on continuous or timed operation.
a)Timed operation
- Select time on E by pressing buttons A and B
- Start by pressing button D
- Stop at the end of the time set, or by pressing button C
Note: The earth values are defi ned according to the residual
differential current. (See NF C 15100 and PROMOTELEC
guidelines). Non-compliance with these instructions may
result in invalidation of the warranty.
In certain circumstances depending
on the sensitivity of the protective cut-
outs, it may be necessary to install
SI-type (super immunity) devices to
prevent untimely triggering.
To PAT test the Electrolux Range of Food Preparation Equipment,
the PCB board needs to be disconnected before any test is done.
This is due to the fact that the boards are fi tted with a grounding
diode that can give incorrect result during such a test. Also on
a standard appliance a fl ash test of 25 amps and up to 3000v is
used but, as you would expect, to use this on equipment, which
has a printed circuit, board would be quite destructive to that
board. We would recommend the use of a PAT tester approved
for computer systems which use a lower rate of amps.
The appliance is perfectly safe and is CE certifi cated. There are
two ways to get overcome this problem.
· Disconnect the board as instructed and test using test for
PC’s,
· Or install the mixer on a fused spur (no plug) as this takes it
away from being a portable appliance and the PAT test is then
not needed.
ATTENTION!!
Clean the machine properly prior to its fi rst use
Uncontrolled closure of the lid or ram press involves a risk of crushing the fi ngers.
Never put a hand in the work area while the machine is in operation; risk of injury. It is strictly for-
bidden to put the safety systems out of action or modify them: Risk of permanent injury!!!!
Check that the safety devices operate correctly each time before using (see paragraph on «safety system checks»).
Never put a hand, a hard or frozen object in the appliance
For health and safety reasons, always use a strong washable or disposable head covering that covers the hair completely.
3
XBB20/30 GB 12 08
