Using the Home Prosafe system
Using the Home Prosafe system
Setting the alarm
The system has two different alarm functions::
1.
ARM AWAY
- Full alarm. All registered Sensors will be activated.
2.
ARM HOME
- Partial alarm All Door/Window sensors will be activated, but the motion detectors are not armed.
This means you can walk around the house, while the ‘shell’ of is protected.
A. A single press arms all Door/Window sensors.
B. A double press of ARM HOME results in every sensor to be active in zones 1-16 but motion detectors are still
not active in in zones 17-30. All Door/Window sensors are however active in zones 17-30.
In ARM HOME mode can your Garage be armed via a motion sensor and the “shell” of your house at the same
time.
Switching on the ARM AWAY function via the console
Press the ARTM AWAY button on the console. The system will be activated after a short delay (delay can be set,
see page 12).During the delay you will hear a couple of tunes at the same pitch. The entry delay will be used for
Ds18 Door/Window sensor (Ds18 switch set to MAX) and motion sensor Ms18 for Zone 15 and 16. when your
enter the house. This means you have enough time to switch off the system via the console without triggering the
alarm. The delay times can be change (see page 12)
Switch on via the Key Remote Control Kr18
Press the ARM button. The alarm is switched on instantly.
Switch on via the Comfort Remote Sh600
Set the slide switch to SEC. Press the ARM AWAY button. The alarm is switched on instantly.
Switching on the ARM HOME function via the console
Press the ARM HOME button on the console. The alarm is switched on instantly.
1. A single press arms all Door/Window sensors.
2. A double press of ARM HOME activates all Sensors in zones 1 - 16.
ARM HOME function cannot be switched on by using key chain remote Kr18 but can be used by remote Sh600.
Panic alarm
The panic alarm can be switched on in case of an emergency, independet of whether the security system is Armed
or Disarmed.
The telephone message indicates the emergancy sensor is triggered and that it is not the burglar alarm. This is
done by adding an extra message to your own spoken telephone message. This standard multi-lingual message is
embedded info the system.
Activate the alarm via the Kr18 Key Chain Remote. Keep the ARM and DISARM buttons of the remote control
pressed simultaneously. The panic alarm is instantly triggered. Depending on the console settings the siren will or
will not be activated.
What happens when the alarm is tripped.
1.
Sirén
- The built-in siren will be activated. You can choose to turn the siren off (silent alarm). If the console is
working on the emergency batteries, the siren will not be used, to save battery power.
2.
The telephone dialler
: - After the last digit of the first telephone number has been dialled, the spoken message
will be played and repeated several times. If the call is answered by pressing 0, the console will stop calling. If the
call is not answered, the second up to the sixth number are dialled until one of these calls is confirmed by pressing
0. The person who receives the phone call can listen to what is going on in the building for one minute. The siren
is switched off while you are listening. The console will remain on alert. If the alarm is triggered again later, the
telephone dialler will be activated again.
Disarming the system
Press DISARM on your remote control. The display will indicate the zone that is causing the alarm. To remove this
message, press ARM and then DISARM.
You can also switch off the system by entering your PIN code on the number pad of the console.
After entering your PIN code the display will read ‘DISARMED’.
Error messages
The number 1-32 in the display refer to up to 32 “zones”. These represent up to 30 Door/Window sensors and/or
Motion detectors you install plus 2 hard wired zones. The numbers show open zones, problem zones and
bypassed zones by beaing displayed as steady on (door or window open), slow flash (there’s problem with that
zone) or a fast flash (that zone has been bypassed). Attempting to armwith an open or problem zone makes the
Console beep continuosly and it will display in words on the display what the cause is, but only for one zone at a
time. Bypassing that zone (by pressing the Clear button) moves on to the next problem zone, if there is one.
The status off all sensors is checked after the security system is switched on. If a problem is found, you will hear
the two-tone ‘problem signal’. If a sensor (e.g.zone 9) indicates there is a problem, a message is shown on the
display:
!
An open window or door: OPEN ZONE 9
.
!
A tamper message: TAMPER ZONE 9
.
!
Empty batteries or range problems: PROBLEM ZONE 9
.
The console and the Ds18 and Ms18 sensors are equipped with a tamper contact. If anyone tries to open the
console or sensor while the alarm is activated, the alarm will trip. If the alarm is NOT activated, you will see an
error message on the console display.8
9
